B310s-22 dead after flashing usbloader
B310s-22 dead after flashing usbloader
(02-12-2018, 01:13 PM)droidmobitech(01-12-2018, 03:53 PM)droidmobitechDevice has been successfully repaired and Unlocked(01-12-2018, 02:29 PM)Sultanpepper Hello,Read Pm and prepare for Remote Assistance
I have flashed a B310s-22 with a usbloader file with Balong usb while attempting to unlock the router. As a result the router is stuck in emergency mode ( no leds working and one COM port working ). I've tried to flash several usbloader files and fixes and each gave as symptom as follows :
1. Power Led working, only one COM port and cannot flash any firmware , DC unlocker doesnt detect anything and Huawei Flasher 1.6 and V2 as well ... nothing works.
2. Power Led works for a couple of seconds then turns off , only one COM port and cannot flash any firmware , DC unlocker doesnt detect anything and Huawei Flasher 1.6 and V2 as well ... nothing works.
3. No Led works , 2 COM ports working and Huawei modem appears in device manager,cannot flash any firmware , DC unlocker doesnt detect anything and Huawei Flasher 1.6 and V2 detects but fails to write the firmware.
4. Ethernet Led blinks periodically , only one COM port and cannot flash any firmware , DC unlocker doesnt detect anything and Huawei Flasher 1.6 and V2 as well ... nothing works.
If i reset power form router it starts in emergency mode again with no leds as stated above.
I would really appreicate if anyone with experience or insight to help out.
Regards
All Done
Problem Solved
Hi I have this same problem .I've tried every single bootloader I could find but the device still wont let me flash it. Please help .
(20-06-2019, 07:53 AM)FaljCracker Hi I have this same problem .I've tried every single bootloader I could find but the device still wont let me flash it. Please help .
(20-06-2019, 01:32 PM)freshtytThanks for the assist .I will work with these and give an update.(20-06-2019, 07:53 AM)FaljCracker Hi I have this same problem .I've tried every single bootloader I could find but the device still wont let me flash it. Please help .
disconnect everything then repeat test point and usb connection then flash usblsafe via balong downloader
after flashing, check device manager and "3G PC UI interface port" should be detected, if so then flash modified firmware higher than the original firmware version of the device
download requirements you need @ https://mega.nz/#F!dfghUAoK!tKaZ-bVxN37F...g!BfhBBAwY
(24-06-2019, 04:22 AM)FaljCrackerHi i tried using the files you sent me but still no luck . once I flash the usblsafeB315.bin the device still remains on one port Huawei mobile connect 3G PC UI interface (boot) . The power led blinks for a few seconds then goes off . I have not been able to get two ports as expected . currently stuck here .(20-06-2019, 01:32 PM)freshtytThanks for the assist .I will work with these and give an update.(20-06-2019, 07:53 AM)FaljCracker Hi I have this same problem .I've tried every single bootloader I could find but the device still wont let me flash it. Please help .
disconnect everything then repeat test point and usb connection then flash usblsafe via balong downloader
after flashing, check device manager and "3G PC UI interface port" should be detected, if so then flash modified firmware higher than the original firmware version of the device
download requirements you need @ https://mega.nz/#F!dfghUAoK!tKaZ-bVxN37F...g!BfhBBAwY