[Please help] Admin Infinix X510 Bricked
[Please help] Admin Infinix X510 Bricked
(02-06-2017, 01:20 AM)Ericko99 Hello admin, my Infinix x510 has bricked. The power button has no effect (my phone doesn't power up) however when i connect the phone to my laptop atleast its detected though it keeps disconnecting.
What i have tried so far:
I have CDC drivers installed for my phone;
I have both SP flash tool and infinix flash tool;
I downloaded this ROM " Infinix X510 Hot 2 (1GB 16 GB) " ht...t=download
From this thread: https://www.hovatek.com/forum/thread-533...Q77t5.dpbs
I have the 1Gb 16Gb variant, after trying to flash this ROM i got the Error: PMT has changed for the ROM after googling for a while for a solution found that i could just format then try downloading the ROM, it didn't work instead i now got this Error: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.
Later on i found this thread " https://www.hovatek.com/forum/thread-439.html " which had suggested some solutions to overcome the latter error but non worked for me. I have even tried flashing the ROM with Infinix flashtool but still get the same error.
Is this ROM a full MTK backup for Infinix X510 1GB 16GB variant please take a look at the attached Image below as it appears in SP flashtool after loading the scatter file.
I have also tried flashing this " Infinix Hot 2 X510-D5110-Androidone-20151012 " ht...G2nhLav57o
but it didn't work.
Please provide me with a full MTK backup for this phone so that i can try flashing it to unbrick this phone.
I am also trying to format my phone and still get the same BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.
Someone please help me figure this out urgently!
Edited: After trying severally to format my phone i have noticed my phone is using USB serial Device instead of the MediaTek Preloader USB VCOM drivers during flashing check out the image i have circled with red i think normally when formating or flashing the Mediatek Preloader USB VCOM drivers should probably appear there now how do i remove this because switching my usb ports still gives me same USB Serial Device driver instead.
(02-06-2017, 01:20 AM)Ericko99 Hello admin, my Infinix x510 has bricked. The power button has no effect (my phone doesn't power up) however when i connect the phone to my laptop atleast its detected though it keeps disconnecting.
What i have tried so far:
I have CDC drivers installed for my phone;
I have both SP flash tool and infinix flash tool;
I downloaded this ROM " Infinix X510 Hot 2 (1GB 16 GB) " ht...t=download
From this thread: https://www.hovatek.com/forum/thread-533...Q77t5.dpbs
I have the 1Gb 16Gb variant, after trying to flash this ROM i got the Error: PMT has changed for the ROM after googling for a while for a solution found that i could just format then try downloading the ROM, it didn't work instead i now got this Error: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.
Later on i found this thread " https://www.hovatek.com/forum/thread-439.html " which had suggested some solutions to overcome the latter error but non worked for me. I have even tried flashing the ROM with Infinix flashtool but still get the same error.
Is this ROM a full MTK backup for Infinix X510 1GB 16GB variant please take a look at the attached Image below as it appears in SP flashtool after loading the scatter file.
I have also tried flashing this " Infinix Hot 2 X510-D5110-Androidone-20151012 " ht...G2nhLav57o
but it didn't work.
Please provide me with a full MTK backup for this phone so that i can try flashing it to unbrick this phone.
I am also trying to format my phone and still get the same BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.
Someone please help me figure this out urgently!
Edited: After trying severally to format my phone i have noticed my phone is using USB serial Device instead of the MediaTek Preloader USB VCOM drivers during flashing check out the image i have circled with red i think normally when formating or flashing the Mediatek Preloader USB VCOM drivers should probably appear there now how do i remove this because switching my usb ports still gives me same USB Serial Device driver instead.
(02-06-2017, 01:44 PM)hovatekIts not X501 rather X510 hope thats a typo error...it shipped with lollipop got a pretty decent marshmallow update however i wanted to downgrade back to lollipop since some xposed modules are not yet fully compatible with Marshmallow.(02-06-2017, 01:20 AM)Ericko99 Hello admin, my Infinix x510 has bricked. The power button has no effect (my phone doesn't power up) however when i connect the phone to my laptop atleast its detected though it keeps disconnecting.
What i have tried so far:
I have CDC drivers installed for my phone;
I have both SP flash tool and infinix flash tool;
I downloaded this ROM " Infinix X510 Hot 2 (1GB 16 GB) " ht...t=download
From this thread: https://www.hovatek.com/forum/thread-533...Q77t5.dpbs
I have the 1Gb 16Gb variant, after trying to flash this ROM i got the Error: PMT has changed for the ROM after googling for a while for a solution found that i could just format then try downloading the ROM, it didn't work instead i now got this Error: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.
Later on i found this thread " https://www.hovatek.com/forum/thread-439.html " which had suggested some solutions to overcome the latter error but non worked for me. I have even tried flashing the ROM with Infinix flashtool but still get the same error.
Is this ROM a full MTK backup for Infinix X510 1GB 16GB variant please take a look at the attached Image below as it appears in SP flashtool after loading the scatter file.
I have also tried flashing this " Infinix Hot 2 X510-D5110-Androidone-20151012 " ht...G2nhLav57o
but it didn't work.
Please provide me with a full MTK backup for this phone so that i can try flashing it to unbrick this phone.
I am also trying to format my phone and still get the same BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.
Someone please help me figure this out urgently!
Edited: After trying severally to format my phone i have noticed my phone is using USB serial Device instead of the MediaTek Preloader USB VCOM drivers during flashing check out the image i have circled with red i think normally when formating or flashing the Mediatek Preloader USB VCOM drivers should probably appear there now how do i remove this because switching my usb ports still gives me same USB Serial Device driver instead.
The problem isn't the driver, your X501 must be a different variant.
What Android version did it ship with and how did the phone get bricked in the first place?
(02-06-2017, 01:51 PM)Ericko99 Its not X501 rather X510 hope thats a typo error...it shipped with lollipop got a pretty decent marshmallow update however i wanted to downgrade back to lollipop since some xposed modules are not yet fully compatible with Marshmallow.
(02-06-2017, 01:54 PM)hovatek(02-06-2017, 01:51 PM)Ericko99 Its not X501 rather X510 hope thats a typo error...it shipped with lollipop got a pretty decent marshmallow update however i wanted to downgrade back to lollipop since some xposed modules are not yet fully compatible with Marshmallow.
Sorry, was a typo.
If removing and reinstalling drivers hadn't helped then yours might've been yet another variant of the X510.
Glad its resolved
(06-06-2017, 03:30 PM)Ericko99 One more thing i have been scouring the internet to find a way to root androidone lollipop on infinix x510
build version Infinix Hot 2 X510-D5110-Andriodone-20151012 using SP flash method but i havn't found anything. I am not really comfortable rooting my phone using Kingroot. Admin can you help me by porting a TWRP version for this ROM i have attached the scatter file, recovery including preloader.bin and lk.bin (all from this ROM ht...G2nhLav57o the one i'm currently runing on my infinix X510 ) to be modified so that i can flash & boot into recovery mode using the button combo.
Scatter file, recovery, preloader.bin and lk.bin can be downloaded from this link.
https://drive.google.com/file/d/0B-OAk_G...sp=sharing