Hovatek Forum MOBILE Android Itel It1520 DRAM_ENABLE_FAIL_(0XFCO)
Can't login? Please, reset your password.
Hovatek is recruiting! Apply Now


Itel It1520 DRAM_ENABLE_FAIL_(0XFCO)

Itel It1520 DRAM_ENABLE_FAIL_(0XFCO)

Pages (3): 1 2 3 Next
r_rocky
r_rocky
r_rocky
Junior Member
17
10-09-2017, 08:03 PM
#1



I was trying to flash the itel it1520 stock rom from your given link in sp flashtool v5 in firmware update mode but after connecting my device it got detected as mediatek usb port(com11) and it starts formating but after some time failed with error
ERROR: S_FT_ENABLE_DRAM_FAIL_(0XFC0)
check your load matches to your target which us to be downloaded.
And now device is bricked not charging no boot loop nothing only detects in sp flash tool after pressing vol down and connecting usb.. And gives me the same error..
.jpg
IMG_20170911_003040.jpg
Size: 94.6 KB / Downloads: 22


Sent from my Redmi 3S using Hovatek Forum
r_rocky
r_rocky
r_rocky
Junior Member
17
10-09-2017, 08:11 PM
#2
There are two variants of stock rom i found on is
1. Itel_IT1520_H358A1_M_IN_160908V65
2. Itel_IT1520_H358A1_M_IN_161024V74

both are giving me the same error.. Tried everything formatting, only flashing preloader bin, untick the lk.bin, flash whole flash except bootloader, format whole falsh, wuth battery without battery..
But always getting the same DRAM ENABLE FAIL.

plz suggest me what to do now..

Sent from my Redmi 3S using Hovatek Forum
hovatek
hovatek
hovatek
Administrator
49,570
11-09-2017, 10:39 AM
#3
(10-09-2017, 08:03 PM)r_rocky I was trying to flash the itel it1520 stock rom from your given link in sp flashtool v5 in firmware update mode but after connecting my device it got detected as mediatek usb port(com11) and it starts formating but after some time failed with error
ERROR: S_FT_ENABLE_DRAM_FAIL_(0XFC0)
check your load matches to your target which us to be downloaded.
And now device is bricked not charging no boot loop nothing only detects in sp flash tool after pressing vol down and connecting usb.. And gives me the same error..

Sent from my Redmi 3S using Hovatek Forum

That was an interruption ; refer to https://www.hovatek.com/forum/thread-808.html
1. Have you tried the fix @ https://www.hovatek.com/forum/thread-439.html ?
2. What was wrong with the phone before you decided to flash?
3. Hope you weren't pressing any button when connecting
This post was last modified: 11-09-2017, 10:44 AM by hovatek.

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.
r_rocky
r_rocky
r_rocky
Junior Member
17
11-09-2017, 11:19 AM
#4
The device has some network issue so i decided to flash..
I downloaded the files from your given links and start flashing in firmware upgrade mode but as i clicked on download and connected my device without battery it got detected as mtk usb port (com11) and start formatting but after some seconds the process automatically interrupt with error DRAM ENABLE FAIL.
Than i read on this forum that it may be firmware mismatch so decided to find any other variant of rom and luckily found v74 and flashed that but always getting the same error..
Sometimes (0XFCO) and sometimes (4032)

Sent from my Redmi 3S using Hovatek Forum
r_rocky
r_rocky
r_rocky
Junior Member
17
11-09-2017, 11:24 AM
#5



I did not pressed any key from first when i try to flash, it automatically detects in sp tool but now as it is hard bricked, i have to press vol down key for getting detected in sp tool..

Sent from my Redmi 3S using Hovatek Forum
xerxes
xerxes
xerxes
Senior Member
8,355
11-09-2017, 02:10 PM
#6
(11-09-2017, 11:24 AM)r_rocky I did not pressed any key from first when i try to flash, it automatically detects in sp tool but now as it is hard bricked, i have to press vol down key for getting detected in sp tool..

Sent from my Redmi 3S using Hovatek Forum

Disconnect the battery and reconnect then retry flashing without holding any key.
r_rocky
r_rocky
r_rocky
Junior Member
17
11-09-2017, 02:17 PM
#7
Tried that also but not detecting in pc, flash tool, no sound.. Only connected when vol key pressed..

Sent from my Redmi 3S using Hovatek Forum
X3non
X3non
X3non
Recognized Contributor
22,062
11-09-2017, 05:14 PM
#8
(11-09-2017, 02:17 PM)r_rocky Tried that also but not detecting in pc, flash tool, no sound.. Only connected when vol key pressed..

Sent from my Redmi 3S using Hovatek Forum

did you by any chance take note of the build number of the device before flashing?
goto the format tab in spft, format all except bootloader
lets know if it formats successfully with a green tick

while at it, also try flashing either of the two firmwares you have using miracle box @ https://www.hovatek.com/forum/thread-14106.html
This post was last modified: 11-09-2017, 05:15 PM by X3non.
r_rocky
r_rocky
r_rocky
Junior Member
17
11-09-2017, 05:38 PM
#9
That's a sad for me that i did not notice the build no..
Formating in sp tool gives the same error DRAM ENABLE FAIL.

Tried in milacle box too but that gave me Bootdata error (2):00

Sent from my Redmi 3S using Hovatek Forum
hovatek
hovatek
hovatek
Administrator
49,570
12-09-2017, 09:17 AM
#10



(11-09-2017, 05:38 PM)r_rocky That's a sad for me that i did not notice the build no..
Formating in sp tool gives the same error DRAM ENABLE FAIL.

Tried in milacle box too but that gave me Bootdata error (2):00

Sent from my Redmi 3S using Hovatek Forum

Yours must be a different variant then.
We'll list the firmware for another Build once available.
BTW, can you get access to a working phone of the same model?

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.
Pages (3): 1 2 3 Next
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)
YtWhTl
live chat
whatsapp telegram instagram