[Please help] S Colo P9 Plus Bricked
[Please help] S Colo P9 Plus Bricked
(27-11-2018, 01:09 PM)raza05 I downloaded & install adb driver from the following thread posted
...
(28-11-2018, 01:19 AM)EMMANUS Is your PC 32 or 64 bit. If your pc is 32 bit, you can install miracle box version 2.02 as it automatically installs all the drivers you need or try miracle drivers found here https://www.hovatek.com/forum/thread-15700.html
(27-11-2018, 06:49 PM)X3non(27-11-2018, 01:09 PM)raza05 I downloaded & install adb driver from the following thread posted
...
Adb driver is not needed, you are to follow the instructions in my previous reply
See https://www.hovatek.com/forum/thread-257...#pid154332
(28-11-2018, 07:21 AM)raza05 well I did try a you instructed uninstall the driver & reinstall first from your page link
https://www.hovatek.com/forum/thread-16640.html
there was error code 10 & driver wasn't installed any how I connect it with miracle 2.27 A & obviously it didnt work like before then I uninstalled it & reinstalled the previous driver which was working on sp flash tool It was successfully installed the version is v1.1236.00 I tried to connect it again with miracle but same error then I connect it with flash tool & it worked screen shots are being attached ..not to mention that I also tried with volume down key in miracle but same driver issue
(28-11-2018, 08:44 AM)X3nonthanks again for the reply finding a pc higher wiindows will be a difficult task for that I have to install windows on one of my running pc it's time consuming but if there is no other option then I have too...I am not insisting on Flash tool but right now this is the only working tool I have ..if you have any other suggestion i'll appreciate ..one more thing is confusing why the same vcom driver working on SP tool not working on miracle box ?(28-11-2018, 07:21 AM)raza05 well I did try a you instructed uninstall the driver & reinstall first from your page link
https://www.hovatek.com/forum/thread-16640.html
there was error code 10 & driver wasn't installed any how I connect it with miracle 2.27 A & obviously it didnt work like before then I uninstalled it & reinstalled the previous driver which was working on sp flash tool It was successfully installed the version is v1.1236.00 I tried to connect it again with miracle but same error then I connect it with flash tool & it worked screen shots are being attached ..not to mention that I also tried with volume down key in miracle but same driver issue
look for a different PC, preferably one running windows 7 or higher
if you still insist on using SPft, then you'll take the long route
backup firmware from your bricked phone using the guide at https://www.hovatek.com/forum/thread-21970.html
you'll get a scatter file after the entire procedure, use the scatter file to flash the files from the volcano backup
(28-11-2018, 12:58 PM)raza05 I tried reading back & ram test with SP Flashtool v.5.1752 here are result attached it's same S_FT_ENABLE_DRAM FAIL (4032) I dont know what's damaging inside but its pretty much bad ... One more thing if any one could explain when I attached the working S-color it pops up message on task bar" MTK pre-loader device found " & installs it but when I connected the bricked one it says "MTK USB device Found " is this causing some thing for phone not to work
(28-11-2018, 12:58 PM)raza05 I tried reading back & ram test with SP Flashtool v.5.1752 here are result attached it's same S_FT_ENABLE_DRAM FAIL (4032) I dont know what's damaging inside but its pretty much bad ... One more thing if any one could explain when I attached the working S-color it pops up message on task bar" MTK pre-loader device found " & installs it but when I connected the bricked one it says "MTK USB device Found " is this causing some thing for phone not to work