Hovatek Forum MOBILE Android Wrr mtk tool+ sp flash tool to back up infinix note 5
Can't login? Please, reset your password.
Hovatek is recruiting! Apply Now


Wrr mtk tool+ sp flash tool to back up infinix note 5

Wrr mtk tool+ sp flash tool to back up infinix note 5

jdalijohn
jdalijohn
jdalijohn
Junior Member
22
09-01-2019, 02:15 PM
#1



While backing up infinix note 5, after read back for the whole rom, i upload it on wwr tool i did not receive an prompting to add preloader file, the button to build firmware is inactive.
Attached Files
.jpg
Capture.JPG
Size: 170.55 KB / Downloads: 12
.jpg
Capture 2.JPG
Size: 179.1 KB / Downloads: 6
EMMANUS
EMMANUS
EMMANUS
Senior Member
1,677
09-01-2019, 08:57 PM
#2
Check your steps again.
You should have 2 read backs , one is Emmc Boot, the other Emmc User.
From the image you posted, you loaded Rom_2 twice, which is not right .

I suggest you start over, and fully understand each step before you proceed .
xerxes
xerxes
xerxes
Senior Member
8,355
09-01-2019, 11:07 PM
#3
(09-01-2019, 02:15 PM)jdalijohn While backing up infinix note 5, after read back for the whole rom, i upload it on wwr tool i did not receive an prompting to add preloader file, the button to build firmware is inactive.

Use the latest version 2.40

Sent from my M5 mini using Hovatek Mobile
jdalijohn
jdalijohn
jdalijohn
Junior Member
22
10-01-2019, 12:44 AM
#4
(09-01-2019, 08:57 PM)EMMANUS Check your steps again.
You should have 2 read backs , one is Emmc Boot, the other Emmc User.
From the image you posted, you loaded Rom_2 twice, which is not right .

I suggest you start over, and fully understand each step before you proceed .
While doing memory test it was only DRam test that was available to i had to create PGDT according to this post
https://www.hovatek.com/forum/thread-22701.html
That is why i have 3 readbacks
jdalijohn
jdalijohn
jdalijohn
Junior Member
22
10-01-2019, 01:12 AM
#5



(09-01-2019, 11:07 PM)innagee
(09-01-2019, 02:15 PM)jdalijohn While backing up infinix note 5, after read back for the whole rom, i upload it on wwr tool i did not receive an prompting to add preloader file, the button to build firmware is inactive.

Use the latest version 2.40

Sent from my M5 mini using Hovatek Mobile

Still the same thing sir
EMMANUS
EMMANUS
EMMANUS
Senior Member
1,677
10-01-2019, 07:16 AM
#6
Note that you are to take a value from here https://www.hovatek.com/forum/thread-22701.html to perform a readback of EMMC User.
After using https://www.hovatek.com/forum/thread-22701.html for step 17 (to obtain the length needed to make a full ROM dump), you have to return to the steps here https://www.hovatek.com/forum/thread-21970.html and continue from 18.
jdalijohn
jdalijohn
jdalijohn
Junior Member
22
10-01-2019, 11:08 AM
#7
(10-01-2019, 07:16 AM)EMMANUS Note that you are to take a value from here https://www.hovatek.com/forum/thread-22701.html to perform a readback of EMMC User.
After using https://www.hovatek.com/forum/thread-22701.html for step 17 (to obtain the length needed to make a full ROM dump), you have to return to the steps here https://www.hovatek.com/forum/thread-21970.html and continue from 18.

I repeated as you stated i still have the result
X3non
X3non
X3non
Recognized Contributor
22,062
10-01-2019, 11:36 AM
#8
(10-01-2019, 11:08 AM)jdalijohn I repeated as you stated i still have the result

i believe you have emmc_boot and emmc_user dumps ready
load emmc_user dump which is rom2 like you did here @ https://www.hovatek.com/forum/attachment.php?aid=6003
then switch to the scatter file tab > expand "cut the rom"
if its active then select and use it

then load the emmc_boot dump
switch to preloader tab > preloader analysis > to extract preloader and save...


BUT if 'cut the rom' is not active, then you will need to manually cut the rom
lets know the outcome and if there's need to manually cut the rom
This post was last modified: 10-01-2019, 11:39 AM by X3non.
jdalijohn
jdalijohn
jdalijohn
Junior Member
22
11-01-2019, 12:40 AM
#9
(10-01-2019, 11:36 AM)X3non
(10-01-2019, 11:08 AM)jdalijohn I repeated as you stated i still have the result

i believe you have emmc_boot and emmc_user dumps ready
load emmc_user dump which is rom2 like you did here @ https://www.hovatek.com/forum/attachment.php?aid=6003
then switch to the scatter file tab > expand "cut the rom"
if its active then select and use it

then load the emmc_boot dump
switch to preloader tab > preloader analysis > to extract preloader and save...


BUT if 'cut the rom' is not active, then you will need to manually cut the rom
lets know the outcome and if there's need to manually cut the rom

Wow i was able to cut the ROM, but the scatter file is missing how do I generate scatter file for what I just cut
X3non
X3non
X3non
Recognized Contributor
22,062
11-01-2019, 10:31 AM
#10



(11-01-2019, 12:40 AM)jdalijohn Wow i was able to cut the ROM, but the scatter file is missing how do I generate scatter file for what I just cut

you can download any scatter file @ https://www.hovatek.com/forum/thread-23512.html
edit the scatter file using notepad or notepad++ then verify the start address and length in the scatter file matches the the address displayed in wwr (it should as its the same note 5) if it does then you can use the scatter file

but if it doesn't match, then modify the values in the scatter file to match what's on wwr
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)
YtWhTl
live chat
whatsapp telegram instagram