Phone not starting after unsuccessful flashing
Phone not starting after unsuccessful flashing
(14-09-2014, 08:02 AM)Androhelp Hello all,
I have a rooted Micromax A58 which was perfectly working. I did a full nandroid backup of it 2 days ago. On yesterday, I was moving some system app (google maps, play store etc) to SD with some software) so that I could increase the internal memory and install some other softwares. But, unfortunately, after that modification, the phone stopped working properly (it was stucking up when the BOLT logo was reached). So, I started it in recovery and do a wipe cache and factory reset. After that, the phone is always going to Factory Mode.
Then I tried to Flash the Stock ROM using Flash Tool but was unsuccessful multiple times. After the scatter file selected, when I clicked the 'Download' (or even firmware upgrade), all time time, the phone was disconnecting/reconnecting every now and then and nothing happened after (even though I already installed the Vcom and PdaNet driver in the PC). So, I had to quit. I am attaching herewith the logs of the Flash Tool lastly tried.
Now, when I am starting the phone power button, nothing is happening.. NOTHING but black screen...
I am now worried.. your helps are very much appreciated. Please let me know for any information needed. Thanks.
(14-09-2014, 11:45 AM)hovatek From the log above, you'll notice the dominance of No COM Port detected. Which means your PC and phone arent communicating OK.
(14-09-2014, 12:44 PM)Androhelp Will go through the link http://www.hovatek.com/forum/thread-286.html you mentioned and revert back. Please let me know if you have any further advice. Thanks.
(14-09-2014, 02:48 PM)hovatek(14-09-2014, 12:44 PM)Androhelp Will go through the link http://www.hovatek.com/forum/thread-286.html you mentioned and revert back. Please let me know if you have any further advice. Thanks.
check this list of SP Flash Tool errors, their meanings and how to resolve them @ http://www.hovatek.com/forum/thread-439.html .... keep us posted
(14-09-2014, 04:42 PM)Androhelp As per your advice, went through the list of SP Flash tool error. Following the below link--
https://hovatek.com/forum/showthread.php?tid=440
I have already downloaded the suggested drivers and installed (please find snapshots attached herewith). But, still the problem there. Neither the device could be recognized nor any progress in the SP Flash activity upon clicking on 'download' and connect the phone.
Also tried different USB port/cable and separate PC.. issue still exists.
Also tried to install PdaNet installer, but as the phone is not getting recognized, so the installation may not be working as expected and resolving the issue.
Please advice further. Thanks.
(14-09-2014, 06:07 PM)hovatekI just tested thoroughly and below is the submission with snapshots (pls co-relate)--(14-09-2014, 04:42 PM)Androhelp As per your advice, went through the list of SP Flash tool error. Following the below link--
https://hovatek.com/forum/showthread.php?tid=440
I have already downloaded the suggested drivers and installed (please find snapshots attached herewith). But, still the problem there. Neither the device could be recognized nor any progress in the SP Flash activity upon clicking on 'download' and connect the phone.
Also tried different USB port/cable and separate PC.. issue still exists.
Also tried to install PdaNet installer, but as the phone is not getting recognized, so the installation may not be working as expected and resolving the issue.
Please advice further. Thanks.
Alright. I need you to observe device manager when you connect the phone to PC without battery inside. observe whether or not it blinks (device manager)
(14-09-2014, 06:45 PM)Androhelp I just tested thoroughly and below is the submission with snapshots (pls co-relate)--
1) When I insert the USB cord in the USB port of PC, the Device Manager blinks (refreshed) and the 'Alcatel Single RNDIS Interface #2' listed in the network adapters in Device Manager (without any exclamation sign) as shown in 'DevMgr_1.png'.
2) Just within 4-5 seconds (instantly), Device Manager again blinks (refreshed) and come to the stage as shown in 'DevMgr_2.png' attached. Alcatel adapter is now having Exclamation sign.
3) The point 1 and point 2 told above go into an endless loop until I remove the phone USB cord from the computer
4) When phone is not attached to computer, the device manager looks like 'When_phone_not_plugged_in.png' attached.
Please go through the snapshots and advice further. Thanks.