Hovatek Forum HARDWARE Repairs [Tutorial] How to fix an Infinix Note 2 X600 totally dead after flashing wrong firmware
Can't login? Please, reset your password.
Hovatek is recruiting! Apply Now


[Tutorial] How to fix an Infinix Note 2 X600 totally dead after flashing wrong firmware

[Tutorial] How to fix an Infinix Note 2 X600 totally dead after flashing wrong firmware

Pages (9): 1 2 3 4 59 Next
mhmyasser
mhmyasser
mhmyasser
Enthusiastic Member
11
17-02-2016, 08:55 PM
#1



!!! PLEASE READ THIS ENTIRE POST BEFORE PROCEEDING !!!
this tutorial applies to all infinx note 2 X600 and it is not require a specified firmware do it when your phone totally dead (no boot, not detected by pc)

WARNING


Do it at your own risk, i'm not responsible for any bricks you may obtain. Please follow the thread rules and steps and everything will be gravy. Remember, select the right firmware for your phone

Requirements


Steps on how to fix an Infinix Note 2 X600 totally dead after flashing wrong firmware


  1. Install the drivers
  2. Identify your board number for the right firmware

    [Image: How-to-fix-an-Infinix-Note-2-X600-totall...ware-1.jpg]

  3. After confirming that you have the right firmware, start xflash tool and load the scatter file then click on start
  4. Only connect the socket in the picture below, then connect the usb cable from the PC to the dead phone. (The PC must not detect the phone at this point)

    [Image: How-to-fix-an-Infinix-Note-2-X600-totall...ware-2.jpg]

  5. Now, make a jumper by connecting a thin piece of wire between the "ground" and the "force boot" pinout.

    [Image: How-to-fix-an-Infinix-Note-2-X600-totall...ware-3.jpg]

    [Image: How-to-fix-an-Infinix-Note-2-X600-totall...ware-4.jpg]

  6. Once your jumper is successful, you'll hear the the connection sound on your PC. The PC will recognize your phone and the xflash tool will begin flashing.

Contributors:
mhmyasser
thanks to "satin" for the pictures
thanks to "hovatek"
This post was last modified: 30-10-2017, 04:26 PM by X3non.
hovatek
hovatek
hovatek
Administrator
49,570
18-02-2016, 12:25 PM
#2
Good one @mhmyasser .
For Tecno D5 users in the same shoes, follow the guide @ https://www.hovatek.com/forum/thread-11802.html

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.
cyblaz
cyblaz
cyblaz
Enthusiastic Member
8
18-02-2016, 03:45 PM
#3
Works like charm..thanks   Smile
mhmyasser
mhmyasser
mhmyasser
Enthusiastic Member
11
18-02-2016, 06:14 PM
#4
At your service Smile
gayus
gayus
gayus
Newbie
4
19-02-2016, 06:54 AM
#5



whoa its work detect my device but somehow i cannot flash it because seems like it always unplug after its plug.. its like the unplug sound hearing right after its detected it... and flash processing take forever


edit : woooaaaa its works you just keep doing the part when 2 jumper conected one time... just keep push it till the flashtool goes into green flash load thank hovatex thanx TS you are really life saver
This post was last modified: 19-02-2016, 07:20 AM by gayus.
hovatek
hovatek
hovatek
Administrator
49,570
19-02-2016, 11:24 AM
#6
Thanks to @mhmyasser

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.
storm52
storm52
storm52
Enthusiastic Member
5
19-02-2016, 04:31 PM
#7
i don't really understand the making a jumper part i connected a network wire to that golden panel don't know where to connect the other end and my computer is yet to detect the phone
storm52
storm52
storm52
Enthusiastic Member
5
19-02-2016, 07:36 PM
#8
finally did the jumper thingy pc now detects the phone but am facing error 3178
hovatek
hovatek
hovatek
Administrator
49,570
19-02-2016, 09:33 PM
#9
(19-02-2016, 07:36 PM)storm52 finally did the jumper thingy pc now detects the phone but am facing error 3178

Screenshot of the error message please

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.
mhmyasser
mhmyasser
mhmyasser
Enthusiastic Member
11
19-02-2016, 10:20 PM
#10



(19-02-2016, 07:36 PM)storm52 finally did the jumper thingy pc now detects the phone but am facing error 3178

did you download and install the drivers from my link just make sure about that and everything will be fine
and read this line carefully
" just make the jumper for one touch don't keep them connected"
This post was last modified: 19-02-2016, 10:22 PM by mhmyasser.
Pages (9): 1 2 3 4 59 Next
Users browsing this thread:
 2 Guest(s)
Users browsing this thread:
 2 Guest(s)
YtWhTl
live chat
whatsapp telegram instagram