Hi, Guest! Login / Register




Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

help with cwm

#1

Hello good morning please I need help with my bricked tecno p5, I understand the procedure of restoring it via cwm, but I don't have cwm and wen I try flashing cwm via mtkdroid tool I get this error message, that the cwm is not suitable for my phone, and wen I click on root it says error coping files between pm and phone


Reply
#2
(01-21-2015, 11:19 AM)godwineze41 Wrote: Hello good morning please I need help with my bricked tecno p5, I understand the procedure of restoring it via cwm, but I don't have cwm and wen I try flashing cwm via mtkdroid tool I get this error message, that the cwm is not suitable for my phone, and wen I click on root it says error coping files between pm and phone

please, list the exact steps you used. might be your method
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#3
(01-21-2015, 11:34 AM)hovatek Wrote:
(01-21-2015, 11:19 AM)godwineze41 Wrote: Hello good morning please I need help with my bricked tecno p5, I understand the procedure of restoring it via cwm, but I don't have cwm and wen I try flashing cwm via mtkdroid tool I get this error message, that the cwm is not suitable for my phone, and wen I click on root it says error coping files between pm and phone

please, list the exact steps you used. might be your method

After downloading and installing pdanet I run mtkdroid tool, I put the phone in factory mode and it showed some Chinese writing I connected the phone and I showed the phone info and there was the yellow spot below the mtkdroid I clicked on root there was a dialogue tab and and I just clicked yes, then it started and at the end it says there was an error coping files between phone and system.
Reply
#4
(01-21-2015, 04:23 PM)godwineze41 Wrote: After downloading and installing pdanet I run mtkdroid tool, I put the phone in factory mode and it showed some Chinese writing I connected the phone and I showed the phone info and there was the yellow spot below the mtkdroid I clicked on root there was a dialogue tab and and I just clicked yes,  then it started and at the end it says there was an error coping files between phone and system.

1. can the phone boot into normal mode?
2. did you click Yes/OK when prompted on PC?
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#5
(01-21-2015, 04:56 PM)hovatek Wrote:
(01-21-2015, 04:23 PM)godwineze41 Wrote: After downloading and installing pdanet I run mtkdroid tool, I put the phone in factory mode and it showed some Chinese writing I connected the phone and I showed the phone info and there was the yellow spot below the mtkdroid I clicked on root there was a dialogue tab and and I just clicked yes,  then it started and at the end it says there was an error coping files between phone and system.

1. can the phone boot into normal mode?
2. did you click Yes/OK when prompted on PC?

It can't boot into normal mode and wen prompted I clicked yes.
Reply
#6
(01-21-2015, 05:59 PM)godwineze41 Wrote: It can't boot into normal mode and wen prompted I clicked yes.

reboot PC and use MTK droid tools v 2.5.3
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#7
(01-21-2015, 07:15 PM)hovatek Wrote:
(01-21-2015, 05:59 PM)godwineze41 Wrote: It can't boot into normal mode and wen prompted I clicked yes.

reboot PC and use MTK droid tools v 2.5.3

Dat it the exact version I'm using
Reply
#8
see wat to do. if your device can be detected by sp flash tool. get a cwm backup from here. jus request. move it to your laptop. also get p5 scatter file. its important. choose the scatter file. choose recovery by ticking it in d list. click to browse it and choose it from the cwm backup. click download. if it doesn't do. choose format without boatloader. the redownload. 08105338813. whatsapp. m using p5

Reply
#9
(01-22-2015, 06:21 AM)godwineze41 Wrote: Dat it the exact version I'm using

might have to fix the phone using AIO flasher or Sp flash tool method. before we proceed, when you boot the phone, whats the color of the TECNO that appears? white or blue?
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#10
(01-22-2015, 11:08 AM)hovatek Wrote:
(01-22-2015, 06:21 AM)godwineze41 Wrote: Dat it the exact version I'm using

might have to fix the phone using AIO flasher or Sp flash tool method. before we proceed, when you boot the phone, whats the color of the TECNO that appears? white or blue?

After pressing the power it brings the tecno then the tecno animation, then it stays on the blue tecno screen
Reply










Users browsing this thread:
1 Guest(s)