Hi, Guest! Login / Register




Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

[Tutorial] How to use SN Write Tool (SN Writer)

#1
(This post was last modified: 07-07-2017, 01:24 PM by hovatek. )

SN Write tool / SN Writer enables you write Bardcode, IMEI, Bluetooth Address, Wi-Fi Address, Ethernet Mac Address, DRMkey MCID and Serial No. to your Mediatek (MTK) Android phone.

Requirements


Note


See the video tutorial below or @ https://youtu.be/BYr7wcvxBvk





How to use SN Writer (SN Write Tool)


  1. Unpack the SN Write tool zip file into a folder and run SN Writer as Administrator

    [Image: how-to-use-SN-writer-1.jpg]

  2. Under ComPort, select USB VCOM

    [Image: how-to-use-SN-writer-2.jpg]

  3. Under Target Type, select your type of device

    [Image: how-to-use-SN-writer-3.jpg]

  4. Click on System Config

    [Image: how-to-use-SN-writer-4.jpg]

  5. The System Config dashboard should pop up

    [Image: how-to-use-SN-writer-5.jpg]

  6. If you wish to write IMEI to the phone then tick IMEI under Write Option. Under IMEI Option, tick the appropriate option (mostly Dual IMEI) depending on the number of SIM card slots the phone has. For the rest like Bluetooth Address, Wi-Fi, Address etc, ticking the box in front of them is just enough

    [Image: how-to-use-SN-writer-6.jpg]

  7. Click the MD1_DB button at the bottom. In the Window that pops up, navigate to the location of the MD1_DB file (usually named like BPLGUInfoCustomAppSrcP_MT65**.....), select it then click Open

    [Image: how-to-use-SN-writer-7.jpg]

  8. Click the AP_DB button at the bottom. In the Window that pops up, navigate to the location of the AP_DB file (usually named like APDB_MT65**.....), select it then click Open

    [Image: how-to-use-SN-writer-8.jpg]

  9. Click Save at the bottom

    [Image: how-to-use-SN-writer-9.jpg]

  10. You should be back to the SN Write tool Home screen, click Start

    [Image: how-to-use-SN-writer-10.jpg]

  11. If you're writing IMEI, enter IMEI 1 and 2 then click OK

    [Image: how-to-use-SN-writer-11.jpg]

  12. If you're writing Bluetooth Address and it is something like bc:b3:08:4c:1f:99 then you simply type bcb3084c1f99 then click OK

    [Image: how-to-use-SN-writer-11b.jpg]

  13. If you're writing Wi-Fi Address and it is something like bc:b3:08:cb:c0:f6 then you simply type bcb308cbc0f6 then click OK

    [Image: how-to-use-SN-writer-11c.jpg]

  14. SN Writer should now display Start searching preloader com port and handshake. At this point, switch off the phone (still with battery inside) and connect it to the PC (do not hold any button on the phone) via a USB cord

    [Image: how-to-use-SN-writer-12.jpg]

  15. You should now see Start searching kernel com port and handshake, just sit back and don't interrupt the process

    [Image: how-to-use-SN-writer-13.jpg]

  16. You'll then see Start switch to MD meta and init Modem database. At this point, the phone will come on. Don't worry, SN Writer is simply booting it into Meta Mode

    [Image: how-to-use-SN-writer-14.jpg]

  17. Next, you'll see Start loop write data to nvram

    [Image: how-to-use-SN-writer-15.jpg]

  18. You should then see Start backup nvram to BinRegion, you're almost done

    [Image: how-to-use-SN-writer-16.jpg]

  19. You should new see a green PASS prompt. You can now disconnect the phone

    [Image: how-to-use-SN-writer-17.jpg]



Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#2
Ends with FAIL Sad
Reply
#3
(07-21-2016, 02:39 PM)robneymcplum Wrote: Ends with FAIL Sad

Check your MD1 or BPG......... file. If possible, get it from a working phone.

Sent from my Infinix-X600 using Hovatek mobile
Reply
#4
Doesn't work don't even try. Needs more explanation on the files. The files I've got from the phone, there were 2 different versions of both. Neither pair have worked. Fail.
Reply
#5
(08-11-2016, 02:09 PM)beratson Wrote: Doesn't work don't even try. Needs more explanation on the files. The files I've got from the phone, there were 2 different versions of both. Neither pair have worked. Fail.

Would help to know the phone model

Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#6
(08-11-2016, 08:12 PM)hovatek Wrote:
(08-11-2016, 02:09 PM)beratson Wrote: Doesn't work don't even try. Needs more explanation on the files. The files I've got from the phone, there were 2 different versions of both. Neither pair have worked. Fail.

Would help to know the phone model

where can i get the AP DB FOR AM USING THE PHONE
Reply
#7
(08-26-2016, 11:09 PM)sherman Wrote: where can i get the AP DB FOR AM USING THE PHONE

Try the one in the official firmware
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#8
Hi,
I keep geting this error.

Phone is a MT6750
Bluboo Maya Max

[Image: 65PD0Hu.png]
Reply
#9
(09-24-2016, 12:57 AM)leemartinc Wrote: Hi,
I keep geting this error.

Phone is a MT6750
Bluboo Maya Max

[Image: 65PD0Hu.png]

The imei is either not correct or complete
Reply
#10
(09-24-2016, 06:38 PM)matybazz Wrote:
(09-24-2016, 12:57 AM)leemartinc Wrote: Hi,
I keep geting this error.

Phone is a MT6750
Bluboo Maya Max

[Image: 65PD0Hu.png]

The imei is either not correct or complete

Not the "Scan Data" Box. The "FAIL" in red behind it.
Reply










Users browsing this thread:
1 Guest(s)