Hi, Guest! Login / Register




Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

[Please help] : NAND Flash was not detected vernee thor new

#1

I got a new phone Vernee Thor 5.0 inch Android 6.0 4G and when i open box wont start(to expensive to return to china i got partial cost covered)i googled and I checked forums.I tray flash with sp tools with apropriet rom it shows ok status and download complet but wont start again it buz but nothing when i push vol+power it does not go to recovery mode only screen becomes brighter ,and nothing hapends.
I did a memory test and it shows ths results Internal RAM:
External RAM:
Type = DRAM
Size = 0xc0000000 (3072MB/24576Mb)
NAND Flash:
ERROR: NAND Flash was not detected!
EMMC:
EMMC_PART_BOOT1 Size = 0x0000000000400000(4MB)
EMMC_PART_BOOT2 Size = 0x0000000000400000(4MB)
EMMC_PART_RPMB Size = 0x0000000000400000(4MB)
EMMC_PART_GP1 Size = 0x0000000000000000(0MB)
EMMC_PART_GP2 Size = 0x0000000000000000(0MB)
EMMC_PART_GP3 Size = 0x0000000000000000(0MB)
EMMC_PART_GP4 Size = 0x0000000000000000(0MB)
EMMC_PART_USER Size = 0x00000003a3e00000(14910MB)
UFS:
ERROR: UFS was not detected!
============ RAM Test ============
Data Bus Test:
[D0]
[D1]
[D2]
[D3]
[D4]
[D5]
[D6]
[D7]
[D8]
[D9]
[D10]
[D11]
[D12]
[D13]
[D14]
[D15]
[D16]
[D17]
[D18]
[D19]
[D20]
[D21]
[D22]
[D23]
[D24]
[D25]
[D26]
[D27]
[D28]
[D29]
[D30]
[D31]
OK!!
Address Bus Test:
[A1]
[A2]
[A3]
[A4]
[A5]
[A6]
[A7]
[A8]
[A9]
[A10]
[A11]
[A12]
[A13]
[A14]
[A15]
[A16]
[A17]
[A18]
[A19]
[A20]
[A21]
[A22]
[A23]
[A24]
[A25]
[A26]
[A27]
[A28]
[A29]
[A30]
[A31]
OK!!
RAM Pattern Test :
Writing ...
0x44332211,
0xA5A5A5A5,
0xA5A5A500,
0xA500A500,
0xA5000000,
0x00000000,
0xFFFF0000,
0xFFFFFFFF,
OK!!
Increment/Decrement Test:
Writing...
OK!!
so i disassembled a battery and repeat process uninstall old drivers and install new ,load prelloder with sp tools only and after that
everything else it shows ok status but memory test shows same results i dont wont to put battery inside until i fix memory if possible


Reply
#2
(08-17-2016, 01:33 PM)fantom2d Wrote: so i disassembled a battery and repeat process uninstall old drivers and install new ,load prelloder with sp tools  only   and after that
everything else it shows ok status but memory test shows same results i dont wont to put battery inside until i fix memory if possible

Try downloading then flashing a different firmware
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply










Users browsing this thread:
1 Guest(s)