[Please help] Admin Infinix X510 Bricked

[Ericko99]

Hello admin, my Infinix x510 has bricked. The power button has no effect (my phone doesn't power up) however when i connect the phone to my laptop atleast its detected though it keeps disconnecting. 

What i have tried so far:

I have CDC drivers installed for my phone;
I have both SP flash tool and infinix flash tool; 
I downloaded this ROM " Infinix X510 Hot 2 (1GB 16 GB) " [ Please, Register to unhide this download link]
From this thread: https://forum.hovatek.com/thread-533.htm...Q77t5.dpbs


I have the 1Gb 16Gb variant, after trying to flash this ROM i got the Error: PMT has changed for the ROM after googling for a while for a solution found that i could just format then try downloading the ROM, it didn't work instead i now got this Error: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.

Later on i found this thread " https://forum.hovatek.com/thread-439.html " which had suggested some solutions to overcome the latter error but non worked for me. I have even tried flashing the ROM with Infinix flashtool but still get the same error.

Is this ROM a full MTK backup for Infinix X510 1GB 16GB variant please take a look at the attached Image below as it appears in SP flashtool after loading the scatter file. 

Capture.PNG Size: 42.82 KB  Downloads: 4

I have also tried flashing this " Infinix Hot 2 X510-D5110-Androidone-20151012 " [ Please, Register to unhide this download link]
but it didn't work.

Please provide me with a full MTK backup for this phone so that i can try flashing it to unbrick this phone.

I am also trying to format my phone and still get the same BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.

Capture 2.PNG Size: 24.88 KB  Downloads: 2

Someone please help me figure this out urgently!

Edited: After trying severally to format my phone i have noticed my phone is using USB serial Device instead of the MediaTek Preloader USB VCOM drivers during flashing check out the image i have circled with red

Capture 4.PNG Size: 57.78 KB  Downloads: 5

i think normally when formating or flashing the Mediatek Preloader USB VCOM drivers should probably appear there now how do i remove this because switching my usb ports still gives me same USB Serial Device driver instead.

[hovatek]

Hello admin, my Infinix x510 has bricked. The power button has no effect (my phone doesn't power up) however when i connect the phone to my laptop atleast its detected though it keeps disconnecting. 

What i have tried so far:

I have CDC drivers installed for my phone;
I have both SP flash tool and infinix flash tool; 
I downloaded this ROM " Infinix X510 Hot 2 (1GB 16 GB) " [ Please, Register to unhide this download link]
From this thread: https://forum.hovatek.com/thread-533.htm...Q77t5.dpbs


I have the 1Gb 16Gb variant, after trying to flash this ROM i got the Error: PMT has changed for the ROM after googling for a while for a solution found that i could just format then try downloading the ROM, it didn't work instead i now got this Error: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.

Later on i found this thread " https://forum.hovatek.com/thread-439.html " which had suggested some solutions to overcome the latter error but non worked for me. I have even tried flashing the ROM with Infinix flashtool but still get the same error.

Is this ROM a full MTK backup for Infinix X510 1GB 16GB variant please take a look at the attached Image below as it appears in SP flashtool after loading the scatter file. 

I have also tried flashing this " Infinix Hot 2 X510-D5110-Androidone-20151012 " [ Please, Register to unhide this download link]
but it didn't work.

Please provide me with a full MTK backup for this phone so that i can try flashing it to unbrick this phone.

I am also trying to format my phone and still get the same BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.


Someone please help me figure this out urgently!

Edited: After trying severally to format my phone i have noticed my phone is using USB serial Device instead of the MediaTek Preloader USB VCOM drivers during flashing check out the image i have circled with red i think normally when formating or flashing the Mediatek Preloader USB VCOM drivers should probably appear there now how do i remove this because switching my usb ports still gives me same USB Serial Device driver instead.

Try uninstalling and re-installing (or updating) VCOM drivers
If the issue persists then your X510 is a different variant

[Ericko99]

Hello admin, my Infinix x510 has bricked. The power button has no effect (my phone doesn't power up) however when i connect the phone to my laptop atleast its detected though it keeps disconnecting. 

What i have tried so far:

I have CDC drivers installed for my phone;
I have both SP flash tool and infinix flash tool; 
I downloaded this ROM " Infinix X510 Hot 2 (1GB 16 GB) " [ Please, Register to unhide this download link]
From this thread: https://forum.hovatek.com/thread-533.htm...Q77t5.dpbs


I have the 1Gb 16Gb variant, after trying to flash this ROM i got the Error: PMT has changed for the ROM after googling for a while for a solution found that i could just format then try downloading the ROM, it didn't work instead i now got this Error: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.

Later on i found this thread " https://forum.hovatek.com/thread-439.html " which had suggested some solutions to overcome the latter error but non worked for me. I have even tried flashing the ROM with Infinix flashtool but still get the same error.

Is this ROM a full MTK backup for Infinix X510 1GB 16GB variant please take a look at the attached Image below as it appears in SP flashtool after loading the scatter file. 

I have also tried flashing this " Infinix Hot 2 X510-D5110-Androidone-20151012 " [ Please, Register to unhide this download link]
but it didn't work.

Please provide me with a full MTK backup for this phone so that i can try flashing it to unbrick this phone.

I am also trying to format my phone and still get the same BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.


Someone please help me figure this out urgently!

Edited: After trying severally to format my phone i have noticed my phone is using USB serial Device instead of the MediaTek Preloader USB VCOM drivers during flashing check out the image i have circled with red  i think normally when formating or flashing the Mediatek Preloader USB VCOM drivers should probably appear there now how do i remove this because switching my usb ports still gives me same USB Serial Device driver instead.

After alot of persistence i finally flashed X510-D5110-Androidone-20151012 ROM

How i did it?  
As earlier mentioned my laptop and SP flashtool was detecting my phone as USB Serial Device so i decided to download new VCOM drivers and latest version of SP flashtool from here http://spflashtool.com/ after uninstalling the existing drivers and reinstalling the new ones my phone was now being detected as an MTK device however i decided to force the computer to use the MediaTek Preloader USB VCOM drivers through the update driver menu.

I tried now to download the ROM using the Download only option but i once again ran into the PMT has changed Error. Tried the Format + Download options and alas! it worked now i have downgraded back to lollipop. However i have lost my IMEI but i was smart enough to write this details somewhere when i first got the phone and it shouldn't be a challenge to restore this.

If you ever, run into problems i am not sure whether this may work for you but it worked for me. Atleast i have figured a way around that annoying BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.

[Ericko99]

Hello admin, my Infinix x510 has bricked. The power button has no effect (my phone doesn't power up) however when i connect the phone to my laptop atleast its detected though it keeps disconnecting. 

What i have tried so far:

I have CDC drivers installed for my phone;
I have both SP flash tool and infinix flash tool; 
I downloaded this ROM " Infinix X510 Hot 2 (1GB 16 GB) " [ Please, Register to unhide this download link]
From this thread: https://forum.hovatek.com/thread-533.htm...Q77t5.dpbs


I have the 1Gb 16Gb variant, after trying to flash this ROM i got the Error: PMT has changed for the ROM after googling for a while for a solution found that i could just format then try downloading the ROM, it didn't work instead i now got this Error: BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.

Later on i found this thread " https://forum.hovatek.com/thread-439.html " which had suggested some solutions to overcome the latter error but non worked for me. I have even tried flashing the ROM with Infinix flashtool but still get the same error.

Is this ROM a full MTK backup for Infinix X510 1GB 16GB variant please take a look at the attached Image below as it appears in SP flashtool after loading the scatter file. 

I have also tried flashing this " Infinix Hot 2 X510-D5110-Androidone-20151012 " [ Please, Register to unhide this download link]
but it didn't work.

Please provide me with a full MTK backup for this phone so that i can try flashing it to unbrick this phone.

I am also trying to format my phone and still get the same BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032) [EMI] Enable DRAM fail.


Someone please help me figure this out urgently!

Edited: After trying severally to format my phone i have noticed my phone is using USB serial Device instead of the MediaTek Preloader USB VCOM drivers during flashing check out the image i have circled with red  i think normally when formating or flashing the Mediatek Preloader USB VCOM drivers should probably appear there now how do i remove this because switching my usb ports still gives me same USB Serial Device driver instead.

The problem isn't the driver, your X501 must be a different variant.
What Android version did it ship with and how did the phone get bricked in the first place?

Its not X501 rather X510 hope thats a typo error...it shipped with lollipop got a pretty decent marshmallow update however i wanted to downgrade back to lollipop since some xposed modules are not yet fully compatible with Marshmallow.

[hovatek]

Its not X501 rather X510 hope thats a typo error...it shipped with lollipop got a pretty decent marshmallow update however i wanted to downgrade back to lollipop since some xposed modules are not yet fully compatible with Marshmallow.

Sorry, was a typo.
If removing and reinstalling drivers hadn't helped then yours might've been yet another variant of the X510.
Glad its resolved

[Ericko99]

Its not X501 rather X510 hope thats a typo error...it shipped with lollipop got a pretty decent marshmallow update however i wanted to downgrade back to lollipop since some xposed modules are not yet fully compatible with Marshmallow.

Sorry, was a typo.
If removing and reinstalling drivers hadn't helped then yours might've been yet another variant of the X510.
Glad its resolved

One more thing  i have been scouring the internet to find a way to root androidone lollipop on infinix x510 
build version Infinix  Hot 2 X510-D5110-Andriodone-20151012 using SP flash method but i havn't found anything. I am not really comfortable rooting my phone using Kingroot. Admin can you help me by porting a TWRP version for this ROM i have attached the scatter file, recovery including preloader.bin and lk.bin (all from this ROM [ Please, Register to unhide this download link]  the one i'm currently runing on my infinix X510 ) to be modified so that i can flash & boot into recovery mode using the button combo.

Scatter file, recovery, preloader.bin and lk.bin can be downloaded from this link.
[ Please, Register to unhide this download link]
 

[hovatek]

One more thing  i have been scouring the internet to find a way to root androidone lollipop on infinix x510 
build version Infinix  Hot 2 X510-D5110-Andriodone-20151012 using SP flash method but i havn't found anything. I am not really comfortable rooting my phone using Kingroot. Admin can you help me by porting a TWRP version for this ROM i have attached the scatter file, recovery including preloader.bin and lk.bin (all from this ROM [ Please, Register to unhide this download link]  the one i'm currently runing on my infinix X510 ) to be modified so that i can flash & boot into recovery mode using the button combo.

Scatter file, recovery, preloader.bin and lk.bin can be downloaded from this link.
[ Please, Register to unhide this download link]
 

Please, create a new thread for this to avoid a mixup
see https://forum.hovatek.com/thread-514.html for how to create a thread