Hi, Guest! Login / Register




Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

[Please help] Miracle box 2.27a

#1

I have noticed this for a while now but it hasnt really bothered me until now that i have this infinix note 2 which is inbuilt battery.please Admins why is it that after any operation done with miracle box one has to pull battery and insert back before the phone can power on or even charge,i don't want to start losing this phone so i won't get into much worse trouble, Any help will be greatly appreciated.


Reply
#2
(06-03-2017, 03:01 PM)Alvincutie Wrote: I have noticed this for a while now but it hasnt really bothered me until now that i have this infinix note 2 which is inbuilt battery.please Admins why is it that after any operation done with miracle box one has to pull battery and insert back before the phone can power on or even charge,i don't want to start losing this phone so i won't get into much worse trouble, Any help will be greatly appreciated.

You don't have to take out and reinsert the battery with Miracle Box so far you didn't interrupt the process
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#3
Actually I normally use miracle box to exit preloader mode if sp flashing was interrupted and the phone is stuck in preloader mode,
Just open miracle box
Do a simple operation like read info and then connect to pc
It should detect the phone that spft can't at that moment and exit preloader after finishing, it takes just a minute or less

Sent from my TECNO Camon CX using Hovatek Forum
Reply
#4
I didnt interupt the process,i even backed up my gionee m3 mini,after the process my phone refused to power on until i removed and inserted the battery again, please is there no other person facing this issue?

Sent from my M3mini using Hovatek mobile
Reply
#5
I even did a simple procees like reading info of my gionee m3 mini,after which it refused to power on or even charge,until i removed the batt.

Sent from my M3mini using Hovatek mobile
Reply
#6
I don't understand what you mean by exiting preloader mode

Sent from my M3mini using Hovatek mobile
Reply
#7
That means I can flash my tecno j8 with miracle box box,please show me how to exit proloader,my phone brick and it can't flash by sp flash tool ,please give me details

Sent from my LW300 using Hovatek Forum
Reply
#8
(06-04-2017, 11:55 PM)Joseph benitez Wrote: That means I can flash my tecno j8 with miracle box box,please show me how to exit proloader,my phone brick and it can't flash by sp flash tool ,please give me details

Sent from my LW300 using Hovatek Forum

Please, stick to your thread, this is someone else's support thread

Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#9
(06-04-2017, 07:31 AM)Alvincutie Wrote: I didnt interupt the process,i even backed up my gionee m3 mini,after the process my phone refused to power on until i removed and inserted the battery again, please is there no other person facing this issue?

Sent from my M3mini using Hovatek mobile

That's weird.
Do you encounter this on a different PC and USB cord?
Also, could you list (step by step) the procedure you normally take when using Miracle Box
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#10
After flashing goes successful pls kindly press and hold the power bottom until the phone switched on.

Like me I always press it like 30 seconds. And it work for me.


Sent from my iPad using Hovatek Forum
Reply










Users browsing this thread:
2 Guest(s)