Hi, Guest! Login / Register




Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

[Please help] Ipad 2 32gb

#1

Pls Hovatek help me on this device after change calibrator on this ipad it refuse to display the back light. I can only seen some image when I set the screen to sun light.
I have try the following process as well:

1) I hold the home bottom + power boton until the ipad restart it still not display.
2) I restore the ipad via itunes and the resrore goes successful but still not work.
3) I open it and check if the display connection was not clip well bit still not work.
4) I plug it to charge till battery was 100% bit it still not work..
Pls may I have clear and confident technique to fix this problem?

Best regards.

Sent from my Infinix X507 using Hovatek Forum


Reply
#2
(This post was last modified: 06-18-2017, 07:04 PM by maxpayne. )
(06-17-2017, 09:48 AM)prince1111 Wrote: Pls Hovatek help me on this device after change calibrator on this ipad it refuse to display the back light. I can only seen some image when I set the screen to sun light.
I have try the following process as well:

1)  I hold the home bottom + power boton until the ipad restart it still not display.
2)  I restore the ipad via itunes and the resrore goes successful but still not work.
3)  I open it and check if the display connection was not clip well bit still not work.
4)  I plug it to charge till battery was 100% bit it still not work..
Pls may I have clear and confident technique to fix this problem?  

Best regards.

Sent from my Infinix X507 using Hovatek Forum

So what you're saying is that the screen is too dim to see anything clearly?

Sent from my Infinix X510 using Hovatek Forum
Reply
#3
Yes

Sent from my Infinix X507 using Hovatek Forum
Reply
#4
The screen is too dim 🔅 to see the image!

Sent from my Infinix X507 using Hovatek Forum
Reply
#5
(06-19-2017, 08:56 AM)prince1111 Wrote: The screen is too dim ? to see the image!

Sent from my Infinix X507 using Hovatek Forum

I think the Backlight chip is not pressed down firmly enough. Check my attachment below maybe it can help point you right

Sent from my Infinix X510 using Hovatek Forum


Attached Files
.jpg   ScreenHunter_185 Jun. 19 10.03.jpg (Size: 159.12 KB / Downloads: 14)
Reply
#6
Every component or chip's in that board is normally 0lace in appropriate way.
And I still press it as well but still n9f work.

Pls help me on this device.

Best regards

Sent from my Infinix X507 using Hovatek Forum
Reply
#7
(06-19-2017, 07:27 PM)prince1111 Wrote: Every component or chip's in that board is normally 0lace in appropriate way.
And I still press it as well but still n9f work.

Pls help me on this device.

Best regards

Sent from my Infinix X507 using Hovatek Forum

Have you changed the backlight chip

Sent from my Infinix X510 using Hovatek Forum
Reply
#8
Nope

Sent from my Infinix X507 using Hovatek Forum
Reply
#9
Which of the chip are talking about an how may I do that...

Best regards

Sent from my Infinix X507 using Hovatek Forum
Reply
#10
(This post was last modified: 06-20-2017, 02:54 PM by hovatek. )
(06-20-2017, 11:22 AM)prince1111 Wrote: Which of the chip are talking about an how may I do that...

Best regards

Sent from my Infinix X507 using Hovatek Forum

Here

[Image: iPad-2-backligvht-chip-min.jpg]

Sent from my Infinix X510 using Hovatek Forum
Reply










Users browsing this thread:
1 Guest(s)