Hi, Guest! Login / Register
Giveaway: Free Hovatek T-shirts, Hoodies & Cufflinks.. I WANT ONE! (Nov 25, 2017)
Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

ULTIMATE GUIDE TO UNLOCK BOOST EVEN MIFI-M023T/M028T [L02B] WITHOUT 16 DIGIT CODE

#1
Star  (This post was last modified: 11-02-2017, 03:58 PM by droidmobitech. )

This device has the Marvell Chipset with few unlock support generally. There many variance of M022, M023 and M028T, which includes L02B, L02C, L02D, and many more WITH LCD AND LED, Dont just try, identify the difference.

Warning; Flashing an incompactible firmware may results to signal damage, searching for network issues and more likely NOT UNLOCKED permanently.


L02C has been successfully Unlocked, will upload soon

This project and it other variance unlock shall remain FREE

NB: It does not support some 4g/LTE after this method for Unlock

It works great on all other 3g networks, few 4g networks are supported. At least better than still locked without help


WARNING

If you cant disassemble and check variance on PCB DONT TRY unless you are very sure about its variance L02B LCD

This guide works on L02B LCD ONLY



NEVER TRY THIS ON L02C AND L02D


ALL REQUIRED FILES POSTED BELOW

1. Download unlock files, as shown in pic

[Image: tut1.png]

[Image: tut2.png]

2. Install WTPTP driver based on x86 and x64 bit

[Image: tut3.png]

3. Install Generic Mifi Drivers manually, locate device manager, add new legacy hardware and proceed to add Marvell AT interface driver manually.

[Image: tut4.png]

[Image: tut5.png]

4. Test quickly for proper installation of Drivers, power on mifi and connect to pc,check in device manager for
1. Not driver with caution, but correctly installed Marvell AT interface driver
2. Marvell DIAG usb devices in usb devices..............may not be seen (not necessarily)


[Image: tut6.png]

5. Disassemble and check pcb of device as shown L02B

[Image: tut7.png]


6. Read instructions in picture

pay attention: the aim is to disconnect the mifi at some % erase flash to allow the device to accept different incompactible loaders somehow....
disconnect mifi at 6-10% erase flash if 3% skipped you so fast

WINDOWS 10 USERS ( ATTENTION)

Wait, pay attention to erase flash and disconnect at ERASE FLASH COMPLETE


DISCONNECT WHEN ERASE FLASH IS COMPLETED


[Image: tut8.png]

[Image: tut9.png]

[Image: tut10.png]

[Image: tut11.png]

[Image: tut12.png]

[Image: tut13.png]

Connect mifi without battery to pc to start flashing

[Image: tut14.png]




7. Flashing the LED firmware, follow same instructions in the picture

a. Open software, Open and select Nehza file to load flash files

b. Tick other non ticked files, select in options erase all flashed

c. proceed to start and connect device without battery again to flash

d. Do not interrupt the flashing, till finish


[Image: tut15.png]

[Image: tut16.png]

[Image: tut17.png]

Disconnect mifi

8. Flashing the Last firmware

a. same as immediate flashing done, Open and select Nehza file to load flash files.

b. tick other files if not already ticked


c. In options Unmark Erase all flash, check and disable erase all flash if already enable in Options (VERY IMPORTANT)

[Image: tut18.png]

[Image: tut19.png]


Disconnect device and insert battery now

Insert non-default sim card, device as for PH-NET PIN,

You will see PH-NET_PIN each time you reset your mifi Unlock code is 123456, DONT FORGET


9.

[Image: tut20.png]

10 . Login to dashboard and type login and password "smartbro" as username and password NOT admin

Skip welcome page, Click on Internet TAB,

Select MEP settings, type Unlock Code as 123456


[Image: tut21.png]

[Image: tut22.png]


11. Unlock Code accepted, please wait, you should see searching for signals on MIFI, it displays the 3g signal of the Sim

NB: It does not support some 4g/LTE after this method for Unlock

It works great on all other 3g networks, few 4g networks are supported. At least better than still locked without help


[Image: tut23.png]

[Image: tut24.png]

[Image: tut25.png]

Tested on GloGH, Vodafone and Tigo, Busy 4g all working perfect

[Image: 20170605_225732.jpg]


DOWNLOAD LINK



[L02C has been successfully Unlocked, will upload soon]



https://goo.gl/7xivJE

No password


All done by droidmobitech

Thanks to Chancellor for donating a device for Trial, First unlock test and tutorial


<TEAM DMT>



Reply
#2
We've got more to offer the world boss! We shall still make a great job!


Sent from my iPhone using Tapatalk
Reply
#3
hello! i have this m028t but my motherboard is l02C_1_30 and my software version is L02CCameroon1_M023_LCD_V005. please how can i unlock his network?
i need a tuto and software to unlock it.
thank you for your help.
Reply
#4
hello! please i need your help to unlock my m028t l02c-1-30 ,firmware version LC02CCameroon1_M023_LCD_V005 . please helpme with the software and tuto.
Email: [email protected]
best regard
Reply
#5
(This post was last modified: 08-19-2017, 08:54 AM by droidmobitech. )
(06-19-2017, 11:38 AM)russelca Wrote: hello! i have this m028t but my motherboard is l02C_1_30 and my software version is L02CCameroon1_M023_LCD_V005. please how can i unlock his network?
i need a tuto and software to unlock it.
thank you for your help.
Reply
#6
(This post was last modified: 08-19-2017, 08:54 AM by droidmobitech. )
(06-19-2017, 12:06 PM)droidmobitech Wrote:
(06-19-2017, 11:38 AM)russelca Wrote: hello! i have this m028t but my motherboard is l02C_1_30 and my software version is L02CCameroon1_M023_LCD_V005. please how can i unlock his network?
i need a tuto and software to unlock it.
thank you for your help.

Chat me for further guidance
Reply
#7
(06-18-2017, 10:35 AM)droidmobitech Wrote: This device has the Marvell Chipset with few unlock support generally. There many variance of M022, M023 and M028T, which includes L02B, L02C, L02D, and many more WITH LCD AND LED, Dont just try, identify the difference.

Warning; Flashing an incompactible firmware may results to signal damage, searching for network issues and more likely NOT UNLOCKED permanently.


L02C has been successfully Unlocked, will upload soon

This project and it other variance unlock shall remain FREE

NB: It does not support some 4g/LTE after this method for Unlock

It works great on all other 3g networks, few 4g networks are supported. At least better than still locked without help


WARNING

If you cant disassemble and check variance on PCB DONT TRY unless you are very sure about its variance L02B LCD

This guide works on L02B LCD ONLY



NEVER TRY THIS ON L02C AND L02D


ALL REQUIRED FILES POSTED BELOW

1. Download unlock files, as shown in pic

[Image: tut1.png]

[Image: tut2.png]

2. Install WTPTP driver based on x86 and x64 bit

[Image: tut3.png]

3. Install Generic Mifi Drivers manually, locate device manager, add new legacy hardware and proceed to add Marvell AT interface driver manually.

[Image: tut4.png]

[Image: tut5.png]

4. Test quickly for proper installation of Drivers, power on mifi and connect to pc,check in device manager for
1. Not driver with caution, but correctly installed Marvell AT interface driver
2. Marvell DIAG usb devices in usb devices..............may not be seen (not necessarily)


[Image: tut6.png]

5. Disassemble and check pcb of device as shown L02B

[Image: tut7.png]


6. Read instructions in picture

pay attention: the aim is to disconnect the mifi at some % erase flash to allow the device to accept different incompactible loaders somehow....
disconnect mifi at 6-10% erase flash if 3% skipped you so fast


[Image: tut8.png]

[Image: tut9.png]

[Image: tut10.png]

[Image: tut11.png]

[Image: tut12.png]

[Image: tut13.png]

Connect mifi without battery to pc to start flashing

[Image: tut14.png]




7. Flashing the LED firmware, follow same instructions in the picture

a. Open software, Open and select Nehza file to load flash files

b. Tick other non ticked files, select in options erase all flashed

c. proceed to start and connect device without battery again to flash

d. Do not interrupt the flashing, till finish


[Image: tut15.png]

[Image: tut16.png]

[Image: tut17.png]

Disconnect mifi

8. Flashing the Last firmware

a. same as immediate flashing done, Open and select Nehza file to load flash files.

b. tick other files if not already ticked


c. In options Unmark Erase all flash, check and disable erase all flash if already enable in Options (VERY IMPORTANT)

[Image: tut18.png]

[Image: tut19.png]


Disconnect device and insert battery now

Insert non-default sim card, device as for PH-NET PIN,

You will see PH-NET_PIN each time you reset your mifi Unlock code is 123456, DONT FORGET


9.

[Image: tut20.png]

10 . Login to dashboard and type login and password "smartbro" as username and password NOT admin

Skip welcome page, Click on Internet TAB,

Select MEP settings, type Unlock Code as 123456


[Image: tut21.png]

[Image: tut22.png]


11. Unlock Code accepted, please wait, you should see searching for signals on MIFI, it displays the 3g signal of the Sim

NB: It does not support some 4g/LTE after this method for Unlock

It works great on all other 3g networks, few 4g networks are supported. At least better than still locked without help


[Image: tut23.png]

[Image: tut24.png]

[Image: tut25.png]

Tested on GloGH, Vodafone and Tigo, Busy 4g all working perfect

[Image: 20170605_225732.jpg]


DOWNLOAD LINK

Password ------Droid.0775

[L02C has been successfully Unlocked, will upload soon]

https://www.dropbox.com/s/jqdrm6fcosqp98...e.rar?dl=0

All done by droidmobitech

Thanks to Chancellor for donating a device for Trial, First unlock test and tutorial


<TEAM DMT>

hi first of all great work but the password o the rar file is not opening it (wrong pass)
Reply
#8
(This post was last modified: 06-30-2017, 11:31 AM by droidmobitech. )
Password-----Droid.0776
Reply
#9
I am waiting thé tutorial for l02c_1_30 m028t.
Reply
#10
(06-26-2017, 08:44 AM)droidmobitech Wrote: Password-----Droid.0776

Bro have tried many times but t shows wrong password... Wats the correct password please
Reply










Users browsing this thread:
1 Guest(s)