Hovatek Forum MOBILE Android [Please help] My infinix note 2 doesn't show network or imei after installing custom ROM
Can't login? Please, reset your password.
Hovatek is recruiting! Apply Now


[Please help] My infinix note 2 doesn't show network or imei after installing custom ROM

[Please help] My infinix note 2 doesn't show network or imei after installing custom ROM

Itz_charlie01
Itz_charlie01
Itz_charlie01
Enthusiastic Member
5
31-12-2017, 04:11 PM
#1



It all started when I downloaded a custom 7.0 ROM for my x600 B1 it installed successfully I even applied the patch for b1 but I noticed that both imei were incomplete and also I couldn't browse or call with full signal bars so I went online for answers I was advised to use champeloeon to change the imei but after doing that my sim wasn't detected this forced me to go back to stock 6.0 which I flashed but after installation I was still seeing unknown baseband,no sim installed, no imei for both sims please help as I currently do not have any where else to turn to or any procedure to follow
xerxes
xerxes
xerxes
Senior Member
8,355
01-01-2018, 12:19 PM
#2
(31-12-2017, 04:11 PM)Itz_charlie01 It all started when I downloaded a custom 7.0 ROM for my x600 B1 it installed successfully I even applied the patch for b1 but I noticed that both imei were incomplete and also I couldn't browse or call with full signal bars so I went online for answers I was advised to use champeloeon to change the imei but after doing that my sim wasn't detected this forced me to go back to stock 6.0 which I flashed but after installation I was still seeing unknown baseband,no sim installed, no imei for both sims please help as I currently do not have any where else to turn to or any procedure to follow

You need to first regain baseband by flashing secro before writing IMEI.
Have you tried flashing the secro.img listed @ https://www.hovatek.com/forum/thread-19960.html
What's your device current build no.?
This post was last modified: 01-01-2018, 12:21 PM by xerxes.
Itz_charlie01
Itz_charlie01
Itz_charlie01
Enthusiastic Member
5
01-01-2018, 02:39 PM
#3
(01-01-2018, 12:19 PM)innagee You need to first regain baseband by flashing secro before writing IMEI.
Have you tried flashing the secro.img
What's your device current build no.?

Tried flashing secro with no luck my build number is X600-H533-B1-M-20160317
Also tried using SN writer but I was getting an error in writing imei same with Maui meta. I download the files needed to flash the imei but I kept on getting errors BTW all my drivers are in order
X3non
X3non
X3non
Recognized Contributor
22,062
01-01-2018, 03:03 PM
#4
(01-01-2018, 02:39 PM)Itz_charlie01 Tried flashing secro with no luck my build number is X600-H533-B1-M-20160317
Also tried using SN writer but I was getting an error in writing imei same with Maui meta. I download the files needed to flash the imei but I kept on getting errors BTW all my drivers are in order

were you able to flash secro successfully?
if yes, then perform a factory reset in recovery mode then check the baseband again
Itz_charlie01
Itz_charlie01
Itz_charlie01
Enthusiastic Member
5
01-01-2018, 04:01 PM
#5



(01-01-2018, 03:03 PM)X3non
(01-01-2018, 02:39 PM)Itz_charlie01 Tried flashing secro with no luck my build number is X600-H533-B1-M-20160317
Also tried using SN writer but I was getting an error in writing imei same with Maui meta. I download the files needed to flash the imei but I kept on getting errors BTW all my drivers are in order

were you able to flash secro successfully?
if yes, then perform a factory reset in recovery mode then check the baseband again
Alright am on it
Itz_charlie01
Itz_charlie01
Itz_charlie01
Enthusiastic Member
5
01-01-2018, 05:15 PM
#6
(01-01-2018, 04:01 PM)Itz_charlie01
(01-01-2018, 03:03 PM)X3non
(01-01-2018, 02:39 PM)Itz_charlie01 Tried flashing secro with no luck my build number is X600-H533-B1-M-20160317
Also tried using SN writer but I was getting an error in writing imei same with Maui meta. I download the files needed to flash the imei but I kept on getting errors BTW all my drivers are in order

were you able to flash secro successfully?
if yes, then perform a factory reset in recovery mode then check the baseband again
Alright am on it
 omg this fixed my issue thanks a lot bro really appreciate. one more question if i try flashing the 7.0 rom, will i still end up with a bricked nvram? what steps should i take to ensure this never happens again?
hovatek
hovatek
hovatek
Administrator
49,570
02-01-2018, 09:38 AM
#7
(01-01-2018, 05:15 PM)Itz_charlie01  omg this fixed my issue thanks a lot bro really appreciate. one more question if i try flashing the 7.0 rom, will i still end up with a bricked nvram? what steps should i take to ensure this never happens again?

Can't say for sure because it depends on what partitions and files the rom changes. If you run into this issue again then simply follow the above fix
This post was last modified: 02-01-2018, 09:39 AM by hovatek.

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.
jhkhkjh
jhkhkjh
jhkhkjh
Newbie
1
22-06-2018, 05:30 PM
#8
(02-01-2018, 09:38 AM)hovatek
(01-01-2018, 05:15 PM)Itz_charlie01  omg this fixed my issue thanks a lot bro really appreciate. one more question if i try flashing the 7.0 rom, will i still end up with a bricked nvram? what steps should i take to ensure this never happens again?

Can't say for sure because it depends on what partitions and files the rom changes. If you run into this issue again then simply follow the above fix
Please how do you run the scero?
xerxes
xerxes
xerxes
Senior Member
8,355
22-06-2018, 06:17 PM
#9
(22-06-2018, 05:30 PM)jhkhkjh
(02-01-2018, 09:38 AM)hovatek
(01-01-2018, 05:15 PM)Itz_charlie01  omg this fixed my issue thanks a lot bro really appreciate. one more question if i try flashing the 7.0 rom, will i still end up with a bricked nvram? what steps should i take to ensure this never happens again?

Can't say for sure because it depends on what partitions and files the rom changes. If you run into this issue again then simply follow the above fix
Please how do you run the scero?

Please create a new thread, this is someone else's support thread. 
See https://www.hovatek.com/forum/thread-514.html for how to create a thread.
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)
YtWhTl
live chat
whatsapp telegram instagram