Hovatek Forum HARDWARE SIM / Network unlock Help
Can't login? Please, reset your password.
Hovatek is recruiting! Apply Now


Help

Help

Pages (3): Previous 1 2 3 Next
X3non
X3non
X3non
Recognized Contributor
22,062
29-03-2018, 04:30 PM
#11



(29-03-2018, 12:27 AM)Baabas drive.google.com/file/d/1r99XvMeqSMU0xEbJdgNHdl1gg7lfUM2r/view?usp=drivesdk

links requires permission
post shareable link OR upload the image to imgur.com or mega.nz
Baabas
Baabas
Baabas
Junior Member
16
29-03-2018, 10:45 PM
#12
[attachment=4867 X3non pid='133042' dateline='1522337404']
.jpg
IMG_20180322_123655 4.jpg
Size: 855.9 KB / Downloads: 6
.jpg
IMG_20180322_123655 4.jpg
Size: 855.9 KB / Downloads: 6
.jpg
IMG_20180322_123655 4.jpg
Size: 855.9 KB / Downloads: 6
.jpg
IMG_20180322_123655 4.jpg
Size: 855.9 KB / Downloads: 6

(29-03-2018, 12:27 AM)Baabas drive.google.com/file/d/1r99XvMeqSMU0xEbJdgNHdl1gg7lfUM2r/view?usp=drivesdk

links requires permission
post shareable link OR upload the image to imgur.com or mega.nz
X3non
X3non
X3non
Recognized Contributor
22,062
30-03-2018, 06:14 PM
#13
(29-03-2018, 10:45 PM)Baabas ...

the picture shows you successfully flashed usbloader
so what error do you get when you try flashing the firmwares and webui?
Baabas
Baabas
Baabas
Junior Member
16
04-04-2018, 09:46 PM
#14
(30-03-2018, 06:14 PM)X3non
(29-03-2018, 10:45 PM)Baabas ...

the picture shows you successfully flashed usbloader
so what error do you get when you try flashing the firmwares and webui?

That's the problem, I formated two devices and after the bar reaches 100% as indicated in the picture, the device will light up and then I go ahead and install the webui and the rest but and normally the bar moves gradually until it reaches 100%,but in this case, the will just reach 100% at a go instead of moving gradually and on reaching 100% the device will not light up which means it's not successful because if I went ahead to install the webui it started searching for the device and will not see it, after waiting it will tell me"device not found.
This post was last modified: 04-04-2018, 09:48 PM by Baabas.
X3non
X3non
X3non
Recognized Contributor
22,062
06-04-2018, 01:00 AM
#15



(04-04-2018, 09:46 PM)Baabas That's the problem, I formated two devices and after the bar reaches 100% as indicated in the picture, the device will light up and then I go ahead and install the webui and the rest but and normally the bar moves gradually until it reaches 100%,but in this case, the will just reach 100% at a go instead of moving gradually and on reaching 100% the device will not light up which means it's not successful because if I went ahead to install the webui it started searching for the device and will not see it, after waiting it will tell me"device not found.

is it the same outcome you get for the two devices?
try powering on the device normally, then see if you are able to detect and connect to the WiFi
Baabas
Baabas
Baabas
Junior Member
16
09-04-2018, 11:38 AM
#16
(06-04-2018, 01:00 AM)X3non
(04-04-2018, 09:46 PM)Baabas That's the problem, I formated two devices and after the bar reaches 100% as indicated in the picture, the device will light up and then I go ahead and install the webui and the rest but and normally the bar moves gradually until it reaches 100%,but in this case, the will just reach 100% at a go instead of moving gradually and on reaching 100% the device will not light up which means it's not successful because if I went ahead to install the webui it started searching for the device and will not see it, after waiting it will tell me"device not found.

is it the same outcome you get for the two devices?
try powering on the device normally, then see if you are able to detect and connect to the WiFi

The last two were successful because after reaching 100%, the device light up and I went ahead and installed the webeu and the update but in this case the device didn't light up, and if I switch it on, it gives me WiFi and can connect, but only MTN
X3non
X3non
X3non
Recognized Contributor
22,062
09-04-2018, 06:26 PM
#17
(09-04-2018, 11:38 AM)Baabas The last two were successful because after reaching 100%, the device light up and I went ahead and installed the webeu and the update  but in this case the device didn't light up, and if I switch it on, it gives me WiFi and can connect, but only MTN

if the device powers on and you can connect to the WiFi, then it surely means somehow usbloader wasn't flashed even though it looks like it was.
whats the firmware and webui version of this particular device?
Baabas
Baabas
Baabas
Junior Member
16
10-04-2018, 11:11 PM
#18
(09-04-2018, 06:26 PM)X3non
(09-04-2018, 11:38 AM)Baabas The last two were successful because after reaching 100%, the device light up and I went ahead and installed the webeu and the update  but in this case the device didn't light up, and if I switch it on, it gives me WiFi and can connect, but only MTN

if the device powers on and you can connect to the WiFi, then it surely means somehow usbloader wasn't flashed even though it looks like it was.
whats the firmware and webui version of this particular device?

Software version: 21.327.62.00.200
Web UI version. : 17.100.18.01.200
X3non
X3non
X3non
Recognized Contributor
22,062
11-04-2018, 06:56 PM
#19
(10-04-2018, 11:11 PM)Baabas Software version: 21.327.62.00.200
Web UI version.  : 17.100.18.01.200

this is a new version. i dont think it will work
This post was last modified: 11-04-2018, 06:58 PM by X3non.
Baabas
Baabas
Baabas
Junior Member
16
12-04-2018, 11:51 PM
#20



(11-04-2018, 06:56 PM)X3non
(10-04-2018, 11:11 PM)Baabas Software version: 21.327.62.00.200
Web UI version.  : 17.100.18.01.200

this is a new version. i dont think it will work

So do you have plans to work on this version?
Pages (3): Previous 1 2 3 Next
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)
YtWhTl
live chat
whatsapp telegram instagram