Hovatek Forum MOBILE Android [Please help] TECNO F2LTE BRICKED
Can't login? Please, reset your password.
Hovatek is recruiting! Apply Now


[Please help] TECNO F2LTE BRICKED

[Please help] TECNO F2LTE BRICKED

Pages (4): Previous 1 2 3 4
X3non
X3non
X3non
Recognized Contributor
22,062
25-08-2018, 07:20 PM
#31



(25-08-2018, 04:51 PM)vavavoom Its not working for me. https://imgur.com/a/zSo3x0J

your screenshot shows you're using F2 DA instead of F2 lte DA also don't load auth file unless required by SPft
vavavoom
vavavoom
vavavoom
Junior Member
28
25-08-2018, 07:40 PM
#32
(25-08-2018, 07:20 PM)X3non
(25-08-2018, 04:51 PM)vavavoom Its not working for me. https://imgur.com/a/zSo3x0J

your screenshot shows you're using F2 DA instead of F2 lte DA also don't load auth file unless required by SPft

My mistake and I actually traced the log for the first flash and it is the F2 LTE DA I used but upload is not working for me. I just tried again with correct DA but same error pls see https://imgur.com/a/zSo3x0J

Pls see the log http://www.mediafire.com/file/rg7q0w0sh3...L.log/file
http://www.mediafire.com/file/u4q8j7e7zy...0.log/file
http://www.mediafire.com/file/lnlnuiwd4g...5.log/file

Thank you very much.
This post was last modified: 25-08-2018, 07:49 PM by vavavoom.
hovatek
hovatek
hovatek
Administrator
49,570
27-08-2018, 10:40 AM
#33
(21-08-2018, 10:38 AM)vavavoom @X3non The phone is not responding to power button. It is still detected by flashtool but it gives many errors when I want to reflash. It shows instant error immediately the phone is detected after clicking download. STATUS_SEC_AUTH file needed.
I added an auth file and it shows instant error STATUS BROM CMD Fail 0xC0060005.
Yes flashing was successful with a green tick. I also did not flash the preloader.
Thank you.

The problem isn't the DA file. The DA file had in fact done its job in enabling the first flash.
Doing a format is one thing that could cause a DA file that once worked to stop working.
When this happens, Sp Flash tool will start asking for an Auth file for subsequent flashes.
I don't know what flash option you selected for the first flash but there's a good chance a format was done.
What 'might' help as this point is a factory firmware

Note!
We have a reply schedule for Free Support. Please upgrade to Private Support if you can't wait.
vavavoom
vavavoom
vavavoom
Junior Member
28
27-08-2018, 11:36 AM
#34
(27-08-2018, 10:40 AM)hovatek
(21-08-2018, 10:38 AM)vavavoom @X3non The phone is not responding to power button. It is still detected by flashtool but it gives many errors when I want to reflash. It shows instant error immediately the phone is detected after clicking download. STATUS_SEC_AUTH file needed.
I added an auth file and it shows instant error STATUS BROM CMD Fail 0xC0060005.
Yes flashing was successful with a green tick. I also did not flash the preloader.
Thank you.

The problem isn't the DA file. The DA file had in fact done its job in enabling the first flash.
Doing a format is one thing that could cause a DA file that once worked to stop working.
When this happens, Sp Flash tool will start asking for an Auth file for subsequent flashes.
I don't know what flash option you selected for the first flash but there's a good chance a format was done.
What 'might' help as this point is a factory firmware

I did not format and I flashed without the preloader. Pls see the flash log I uploaded. Is there a way to get a factory firmware?
X3non
X3non
X3non
Recognized Contributor
22,062
27-08-2018, 05:15 PM
#35



(27-08-2018, 11:36 AM)vavavoom I did not format and I flashed without the preloader. Pls see the flash log I uploaded. Is there a way to get a factory firmware?

nobody said you formatted on purpose but from all your trials, you might have done so without knowing [e.g you can select format all + download or even firmware upgrade, format might go successfully and download fails] 
anyway only OEMs in your case Tecno can release factory firmware
kagbontaen
kagbontaen
kagbontaen
Techie Member
44
19-10-2018, 06:04 PM
#36
while attempting to reset frp on my f2lte it got bricked as i was using sp flash tool to format the address of the frp.bin. now its asking for the auth file which nobody in the entire 25 exabyte of internet seems to have.
i'd be more than greatful if you guys can help me get it. 
f2lte auth file.
you can contact me at kinc7775@gmail.com
please help
This post was last modified: 19-10-2018, 06:07 PM by kagbontaen. Edit Reason: incomplete reply
xerxes
xerxes
xerxes
Senior Member
8,355
20-10-2018, 01:18 AM
#37
(19-10-2018, 06:04 PM)kagbontaen while attempting to reset frp on my f2lte it got bricked as i was using sp flash tool to format the address of the frp.bin. now its asking for the auth file which nobody in the entire 25 exabyte of internet seems to have.
i'd be more than greatful if you guys can help me get it. 
f2lte auth file.
you can contact me at kinc7775@gmail.com
please help

Please create a new thread, this is someone else's support thread.
See https://www.hovatek.com/forum/thread-514.html for how to create a thread.
chrisbanks09
chrisbanks09
chrisbanks09
Newbie
2
29-01-2019, 01:56 AM
#38
*****
This post was last modified: 29-01-2019, 10:29 AM by X3non.
Pages (4): Previous 1 2 3 4
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)
YtWhTl
live chat
whatsapp telegram instagram