hard bricked tecno ca8
hard bricked tecno ca8
(06-09-2019, 12:42 PM)Barimaba Qwaku Acquah hello please my tecno ca8 has hard bricked and am trying to flash it but sp flash after inserting the usb in my phone gives error STATUS_BROM_CMD_FAIL {C0x0060005}
how it came about was, i was using it and it freezed so i off it by pressing and holding power button for some seconds and it never came back on again till now
(06-09-2019, 06:06 PM)hovatek That's because your phone needs a DA file for flashing. Refer to https://www.hovatek.com/forum/thread-23243.html
Hope the firmware you're trying to flash is of the same build number as your phone's
(06-09-2019, 07:00 PM)Barimaba Qwaku Acquah i have downloaded the DA file from here but its still not working and yes i have the build number for it
About 4months ago i had the same problem when rooting the phone but through hovatek i could flash it successfully with the firmware and the DA file am trying to use now. after i successfully rooted it with MAGICDISK. but now when i try flashing it the DA file does not download to turn red, ERROR_BROM_CMD_FAIL {C0x0060005}
(07-09-2019, 11:11 AM)X3non(06-09-2019, 07:00 PM)Barimaba Qwaku Acquah i have downloaded the DA file from here but its still not working and yes i have the build number for it
About 4months ago i had the same problem when rooting the phone but through hovatek i could flash it successfully with the firmware and the DA file am trying to use now. after i successfully rooted it with MAGICDISK. but now when i try flashing it the DA file does not download to turn red, ERROR_BROM_CMD_FAIL {C0x0060005}
loosen the back cover, disconnect / reconnect the battery then attempt to reflash (still using the custom DA)
(07-09-2019, 01:25 PM)Barimaba Qwaku Acquah I have tried several times, i have removed the the battery and inserted it but still, when i plug in the dead phone and check my device manager, what i see is USB SERIAL DEVICE but i have installed the vcom drivers successfully and its not showing when i plug in the phone
(07-09-2019, 03:11 PM)X3non(07-09-2019, 01:25 PM)Barimaba Qwaku Acquah I have tried several times, i have removed the the battery and inserted it but still, when i plug in the dead phone and check my device manager, what i see is USB SERIAL DEVICE but i have installed the vcom drivers successfully and its not showing when i plug in the phone
update that usb serial.. to vcom preloader using the guide @ https://www.hovatek.com/forum/thread-16839.html then retry flashing
(08-09-2019, 11:02 AM)Barimaba Qwaku Acquah i did it and when i try flashing with techno flash tool {SWS aftersales} its able to detect but get stuck on DA connecting and about 2mins it gives me error DA CONNECTION FAIL STATUS_PROTOCOL_ERROR
(09-09-2019, 10:42 AM)X3non(08-09-2019, 11:02 AM)Barimaba Qwaku Acquah i did it and when i try flashing with techno flash tool {SWS aftersales} its able to detect but get stuck on DA connecting and about 2mins it gives me error DA CONNECTION FAIL STATUS_PROTOCOL_ERROR
are you holding any button(s) when you connect the phone for flashing?
try flashing with and without the battery connected, both attempts without holding any button before connecting the phone to the PC
(09-09-2019, 04:34 PM)Barimaba Qwaku Acquahyou have an auth_sv5.auth file(09-09-2019, 10:42 AM)X3nonTHIS ARE WHAT AM TALKING ABOUT BOSS(08-09-2019, 11:02 AM)Barimaba Qwaku Acquah i did it and when i try flashing with techno flash tool {SWS aftersales} its able to detect but get stuck on DA connecting and about 2mins it gives me error DA CONNECTION FAIL STATUS_PROTOCOL_ERRORare you holding any button(s) when you connect the phone for flashing?
try flashing with and without the battery connected, both attempts without holding any button before connecting the phone to the PC