Hovatek Forum MOBILE Android My Tecno F1 power on Fast boot Mode
Can't login? Please, reset your password.
Hovatek is recruiting! Apply Now


My Tecno F1 power on Fast boot Mode

My Tecno F1 power on Fast boot Mode

Dbabs
Dbabs
Dbabs
Junior Member
30
31-08-2020, 01:39 PM
#1



My Tecno F1 Always on to Fastboot mode When Ever I power it on.. I have Change the Power key both volume key but Not still Work

Sent from my TECNO KB7 using Hovatek Mobile
This post was last modified: 31-08-2020, 03:19 PM by Dbabs.
Chijohn
Chijohn
Chijohn
Junior Member
36
31-08-2020, 07:53 PM
#2
(31-08-2020, 01:39 PM)Dbabs My Tecno F1 Always on to Fastboot mode When Ever I power it on.. I have Change the Power key both volume key but Not still Work

Sent from my TECNO KB7 using Hovatek Mobile
Reboot to recovery mode then check the build number of the phone. download  your phone build  number from here  https://www.hovatek.com/forum/thread-26041.html

Use software download aftersales tools to flash the phone.
X3non
X3non
X3non
Recognized Contributor
22,062
01-09-2020, 01:14 PM
#3
(31-08-2020, 01:39 PM)Dbabs ...

...link to SWD tool @ https://www.hovatek.com/forum/thread-23709.html
Dbabs
Dbabs
Dbabs
Junior Member
30
02-09-2020, 12:46 PM
#4
SWD flash tools didnt work in system please is their Any other Way

Sent from my TECNO KB7 using Hovatek Mobile
Chijohn
Chijohn
Chijohn
Junior Member
36
02-09-2020, 07:35 PM
#5



(02-09-2020, 12:46 PM)Dbabs SWD flash tools didnt work in system please is their Any other Way
Sent from my TECNO KB7 using Hovatek Mobile
 
 Its will be better you take it to an experienced  software  engineer who is in charge of cm2mtk2.. I still rectified the same phone today with fastboot problem.The person must untick preloader. Every other  thing can remain the same.I will post log of my work very soon while using cm2mtk2.
Chijohn
Chijohn
Chijohn
Junior Member
36
03-09-2020, 03:39 AM
#6
read_info

Code:

Operation : Identify [ v2.11 ]
Mode : FLASH

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM35)
MODE : PRELOADER PORT
PORT : 35
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
    CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
    TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode  : PLAIN [+PRL]
BROM : BROM|BL  : 0xFF|0x01
BROM : PRELOADER PORT
MODE : 0_base : BASE_v2012 | Manual : Enabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_SWSEC.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
    BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
    DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 484A019061344738221FA5327D8609DC
DAInf: 4 : 2 : 156
    DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

        EMMC: 90014A483847346132A51F22DC09867D
        EMMC: VEN : HYNIX | OEM : 4A01 | DEV : H8G4a2
        EMMC:
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB  : 0x00400000 [ 4.00 MB ]
              USER  : 0x1D2000000 [ 7.28 GB ]

        SRAM: 0x00020000 [ 128.00 KB ]
        DRAM: 0x40000000 [ 1.00 GB ]

        CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 6C31F8CF988D5DB42A1AAD3663033287

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

Patch Level    : O11019
Display ID    : F1-VP510EFG-GO-200304V18
Ver. CodeName  : REL
Ver. Release  : 8.1.0
Sec. Patch    : 2020-03-05
Build Time    : 1583311585
Product Model  : TECNO F1
Product Brand  : TECNO
Product Name  : VP510
Product Device : TECNO-F1-PRO
Product Manfct : TECNO MOBILE LIMITED
Product Info  : k80_bsp
Product Board  : F1
Board Platform : mt6580

USERDATA : ENCRYPTED


Done!
Elapsed: 00:00:18


write firmware
Code:

Preloader [HW DEV] Info :
EMI : DEV : MT6752
EMI : SRC : preloader_k80_bsp.bin
EMI : CNT : 0003
EMI : [00] : eMMC : DDR3 : ID : 150100464E36324D42 : VEN : SAMSUNG  | DEV : FN62MB : RAM : [ 1.00 GB ]
EMI : [01] : eMMC : DDR3 : ID : 700100454838454538 : VEN : KINGSTON  | DEV : EH8EE8 : RAM : [ 1.00 GB ]
EMI : [02] : eMMC : DDR3 : ID : 150100464E58324D42 : VEN : SAMSUNG  | DEV : FNX2MB : RAM : [ 1.00 GB ]

Operation : Write Flash [ v2.11 ]

Repartition  : Enabled
Flash Verify  : Disabled
Reg.Pre-Erase : Enabled
Verify HW/SW  : Enabled
SData Backup  : Disabled
Safe UserData : Disabled
Flash Format  : Disabled

Files :13
[FL] : Set : lk-sign.img
[FL] : Set : lk-sign.img
[FL] : Set : boot-sign.img
[FL] : Set : recovery-sign.img
[FL] : Set : logo-sign.bin
[FL] : Set : odmdtbo-sign.img
[FL] : Set : vendor-sign.img
[FL] : Set : tee-sign.img
[FL] : Set : tee-sign.img
[FL] : Set : secro-sign.img
[FL] : Set : system-sign.img
[FL] : Set : cache-sign.img
[FL] : Set : userdata-sign.img

[FL] : Total size : 0x51DDBAD4 [ 1.28 GB ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM35)
MODE : PRELOADER PORT
PORT : 35
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
    CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
    TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode  : PLAIN [+PRL]
BROM : BROM|BL  : 0xFF|0x01
BROM : PRELOADER PORT
MODE : 0_base : BASE_v2012 | Manual : Enabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_SWSEC.bin
AGENT : Found MT6580
AGENT : MTK_DOWNLOAD_AGENT
    BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
    DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 484A019061344738221FA5327D8609DC
DAInf: 4 : 2 : 156
    DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

        EMMC: 90014A483847346132A51F22DC09867D
        EMMC: VEN : HYNIX | OEM : 4A01 | DEV : H8G4a2
        EMMC:
              BOOT1  : 0x00400000 [ 4.00 MB ]
              BOOT2  : 0x00400000 [ 4.00 MB ]
              RPMB  : 0x00400000 [ 4.00 MB ]
              USER  : 0x1D2000000 [ 7.28 GB ]

        SRAM: 0x00020000 [ 128.00 KB ]
        DRAM: 0x40000000 [ 1.00 GB ]

        CHIP : MT6580 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

        RNID : 6C31F8CF988D5DB42A1AAD3663033287

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

[FL] : HW verification passed!

SEC_DL : True (CUST)
SEC_DL : SECURE USB DL ENABLED
SEC_ID : 0x35464646304237304435444533464335

[FL] : Pre-Erase
Erase : 0x0000000000000000 : 0x0000000000080000
Erase : 0x0000000004C80000 : 0x00000000DC380000

[FL] : RePartition
[FL] : RePartition Ok!

SecInit : LK
SecInit : LK2
SecInit : BOOT
SecInit : RECOVERY
SecInit : LOGO
SecInit : ODMDTBO
SecInit : VENDOR
SecInit : TEE1
SecInit : TEE2
SecInit : SECRO
SecInit : SYSTEM
SecInit : CACHE
SecInit : USERDATA

[FL] : Flashing now ...

Write : LK
Write : LK2
Write : BOOT
Write : RECOVERY
Write : LOGO
Write : ODMDTBO
Write : VENDOR
Write : TEE1
Write : TEE2
Write : SECRO
Write : SYSTEM
Write : CACHE
Write : USERDATA

SEC_DL : WRITE INFO : OK


[FL] : RePartition
[FL] : RePartition Ok!

[FL] : Flashing finished!

Done!
Elapsed: 00:01:58

after successful flashing I ALWAYS compare THE build to know if it is emmc problem. i.e readinfo again.
This post was last modified: 03-09-2020, 10:19 AM by X3non.
X3non
X3non
X3non
Recognized Contributor
22,062
03-09-2020, 10:17 AM
#7
(02-09-2020, 12:46 PM)Dbabs SWD flash tools didnt work in system please is their Any other Way

Sent from my TECNO KB7 using Hovatek Mobile

you'll need to explain what you mean by didn't work and attach screenshot of error message encountered
Users browsing this thread:
 1 Guest(s)
Users browsing this thread:
 1 Guest(s)
YtWhTl
live chat
whatsapp telegram instagram