Hi, Guest! Login / Register




Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

HELP!!! tecno d5

#11

(08-01-2014, 06:11 PM)hovatek Wrote: you'll need to comment out those two

How am ι тσ do that? ..cos ι tried adding __NOdl_ in front of em ..then reselected the scatter file ..thus they didn't appear on the list this time ..that was the only way ι could use firmware upgrade ..buh it didn't work ..gave error about pmt that ι should use DOWNlOad instead


Reply
#12
(08-01-2014, 07:38 PM)X3non Wrote: How am ι тσ do that? ..cos ι tried adding __NOdl_ in front of em ..then reselected the scatter file ..thus they didn't appear on the list this time ..that was the only way ι could use firmware upgrade ..buh it didn't work ..gave error about pmt that ι should use DOWNlOad instead

Download and install Notepad++
Open the scatter file using Notepad++
Delete the following lines in the scatter file then save
}
SEC_RO 0xe80000
{

and

}
CACHE 0x12ba0000
{

Ensure to delete any blank row so there's no space. Now, try loading scatter file again
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#13
(This post was last modified: 08-01-2014, 10:49 PM by X3non. )
Spf tool v3 ..give the error
(Warning hint) get BMT block count fail, default BMT block count is used!

Now if ι click ok тσ proceed тσ firmware upgrade

It now gives the error
SP FLASH TOOL ERROR : (8045)
No valid partition management table(PMT) ƒσʀ storage device!
(HINT):
Please make sure there is α correct load in the target.
Firmware upgrade could not вє executed without PMT!
Please "download" only first тσ create PMT on the target

Spf tool v5 on the other hand doesn't give any errors when ι select scatter file

Buh when ι click firmware upgrade ..it gives the error
_NODL_NVRAm: failed тσ get PMT info
Reply
#14
(This post was last modified: 08-01-2014, 11:18 PM by hovatek. )
(08-01-2014, 10:45 PM)X3non Wrote: Spf tool v3 ..give the error
(Warning hint) get BMT block count fail, default BMT block count is used!

Now if ι click ok тσ proceed тσ firmware upgrade

It now gives the error
SP FLASH TOOL ERROR : (8045)
No valid partition management table(PMT) ƒσʀ storage device!
(HINT):
Please make sure there is α correct load in the target.
Firmware upgrade could not вє executed without PMT!
Please "download" only first тσ create PMT on the target

Spf tool v5 on the other hand doesn't give any errors when ι select scatter file

Buh when ι click firmware upgrade ..it gives the error
_NODL_NVRAm: failed тσ get PMT info

OK, replace the modified scatter file with the original, we're going to do another modding
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#15
list all the versions of SP flash tool you have

Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#16
V3.1316
V3.1324
V3.1328
V5.1352.01
Reply
#17
(08-02-2014, 08:33 AM)X3non Wrote: V3.1316
V3.1324
V3.1328
V5.1352.01

what's your email address? wanna send you modded secro and cache files
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#18
(This post was last modified: 08-02-2014, 10:06 PM by X3non. )
[email protected]

[email protected]
Тнαηкѕ
Reply
#19
(08-02-2014, 09:48 PM)X3non Wrote: [email protected]
Тнαηкѕ

check your email
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#20
Downloaded it ..and tried it with v5 and v1328 ..both gave me the same errors they have been giving me both with download and firmware upgrade
Reply










Users browsing this thread:
1 Guest(s)