Hi, Guest! Login / Register
Giveaway: Free Hovatek T-shirts, Hoodies & Cufflinks.. I WANT ONE! (Nov 25, 2017)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

[Please help] No recovery on Tecno D3

#11

I've already set up a ADB on my computer, what I'm trying to say is there's no way I can access the phone settings so that I can enable the ADB that is what I'm saying I can't enable it because the phone is locked with a pattern and I can't access it. Please what else can I do


Reply
#12
(06-26-2015, 01:55 PM)adutwumraymond Wrote: I've already set up a ADB on my computer, what I'm trying to say is there's no way I can access the phone settings so that I can enable the ADB that is what I'm saying I can't enable it because the phone is locked with a pattern and I can't access it. Please what else can I do

boot the phone into factory mode (volume down + power button) then try adb again
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#13
i've already setup adb on my laptop, i've been using it for three years. what i mean is i cant connect adb on my phone cause thers no way to switch it ON.
Please tell me how to flash it with sp flash tool cause my phone can't connect with my computer and i have install all the drivers
Reply
#14
(07-01-2015, 08:15 PM)adutwumraymond Wrote: i've already setup adb on my laptop, i've been using it for three years. what i mean is i cant connect adb on my phone cause thers no way to switch it ON.
Please tell me how to flash it with sp flash tool cause my phone can't connect with my computer and i have install all the drivers

ok. 
1. if you dont have the stock backup for D3 then supply a gmail address for ours
2. as for SP flash tool not detecting the phone, ensure to install vcom drivers using https://forum.hovatek.com/thread-440.html
next, connect the phone to PC and observe if device manager refreshes when the phone gets connected. if the phone gets detected in device manager, let me know what it gets detected as
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#15
When I plug it in it shows SCI General US2(AT)(COM 11) and SCI Vendor US2(DIAG)(COM12)
Reply
#16
(07-03-2015, 06:36 PM)adutwumraymond Wrote: When I plug it in it shows SCI General US2(AT)(COM 11) and SCI Vendor US2(DIAG)(COM12)

that looks like Spreadtrum. seems your own D3 is spreadtrum phone. that would explain a lot if true.
try booting into recovery mode using this guide @ https://forum.hovatek.com/thread-2167.html
let me know how it goes
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply
#17
Admin, I tried but no luck. I did some research and apparently it can be flashed with flash tool and a PAC file.
I was hoping you'll a link to download that file
Reply
#18
(07-13-2015, 01:58 PM)adutwumraymond Wrote: Admin, I tried but no luck. I did some research and apparently it can be flashed with flash tool and a PAC file.
I was hoping you'll a link to download that file

we dont have the pac format of the firmware
Need further assistance? Speak with a Hovatek Representative:
Working Hours: Mondays - Saturdays ; 09:00 - 18:00 (GMT +1:00)
Reply










Users browsing this thread:
1 Guest(s)